Hello Nordic Team,
I have a working project that uses BLE to communicate with a mobile app, and I am now looking to integrate Google Fast Pair as an additional feature....
Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
I've been working on a separate problem with the NFC Type 4 library when I ran across this. I can duplicate it in the experimental_writeable_ndef_msg example.
All I did...
Hi Nordic Forum!
I've been trying to run a test program (pin toggle) on a custom nRF52832 board.
First, I tried the same program on the HDK to toggle pin P0.17 (LED1...
When I use additional VS UUID, should I use sd_ble_uuid_vs_add(), se_ble_gatts_service_add() in order?
example,
sd_ble_uuid_vs_add(); <- VS1 UUID
se_ble_gatts_service_add...
Hello, I am developing with pc-ble-driver using python. I noticed that the Bluetooth connection becomes disconnected when I alt tab out of the gui I made. Is there a solution...
Hello,
I am using SEGGER Embedded Studio together with a nRF52832 and I am trying to read an EEprom register containing a 32-bit floating point value in four bytes (register...
Hi,
I try to use the BLE to send data to a smartphone but I have a issue when I try to flash my nRF52 DK, using eclipse. I get the following error :
No source available...
I am using the example ble central devices from the SDK 8.1. The example provided prints out to pin 19 (the on-board LED). I wanted to change the functionality to print to...
I am trying to add ADC to my program per the nordic examples on GitHub.
Using GCC, SDK12, nrf51.
These are the errors I am getting: (sorry for the formatting of this - code...
Hi,
SDK12 does not have Pstorage. I want to show you how to add it.
Steps:
Copy the pstorage folder in SDK11 into the SDK12 \components folder.
Open...
Hello,
I've been working on a project for some time now and prototyping it with replacement atmel ic's like the at mega328 and bluetooth modules and other stuff in the...
My custom board sometimes freezed on initialization process of bootloader (SDK11 dual_bank_ble_s130) when after long running and reconnect the power.
However the symptoms...
I am running the ble_app_hrs example and it runs as expected.
However, I tried removing one or more of the services from services_init as well as the corresponding advertisement...
I implement a card emulation and the card itself doesn't conform to 14443A-3 crc check. I need to disable crc check on card selected event
NRF_NFCT->RXD.FRAMECONFIG...
I've been running a hand soldered prototype board for about a week in an outdoor location where it gets hot and cold (mainly hot), and I noticed it was no longer visible on...
