Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hi, I am using following code inside for(;;) in main function
if(diff == 30)
advertising_stop();
else if(diff == 60)
advertising_start();
Following are the advertising_start...
I use IAR to debug nRF51_SDK12.0.0 ble_app_uart example application. The origin application is for nrf51422, and my device use nrf51822. Therefore, I first change the device...
I'm using a S130 on nrf51822.
connect to 3 peripherals (in case of the master)
connect to 1 central (in case of the slave)
But, I want to use 1 peripheral and 1 centeral...
I'm using nRF52+SDK11.0.0+S132 with an application based on the ble_hrs example.
In main() , if I call a blocking nrf_drv_spi_transfer() to configure some SPI sensors before...
Hello I tried to do a application update with my own key and it does work.
But then I tried to create zip with all 3 parts: APP+BL+SD (application+BootLoader+SoftDevice...
Hi
With the introduction of softdevice v2.0.1, the connection bandwidth has become configurable to be low, medium, or high; and can be specified independently for TX And...
Hi,
Now I'm using nRF52 SDK v12 and S132, I have some data(about 300 bytes)need to write to the flash. I have seen the fstorage but I donn't know how to use it. Could anyone...
Hi,
I am trying to implement a biometric group telemetry system for my gym and experimentation.
In the past I used a nRF24AP2 module and an ARDUINO PRO MINI 3.3V 8MHz...
Hii,
I want to assign name to my custom service. how can i add it i am using nrf52 chip and s132 softdevice.
I have add new service using sd_ble_gatts_service_add() A...
In my project I need to be able to get time from a continuously running RTC. The softdevice uses RTC0, and app_timer uses RTC1 (and starts and stops it).
(annoyingly I...
Hi ,
I am working on one application in which i am using UART service. Whenever i am connecting to device using nrf connect or master control pannel app, UART service empty...
Hello.
I use the BLE multilink central example to connect to 2 sensors. I changed the example in that way that i successfully connect and read data from a Wahoo Cadence...
the application is examples\peripheral\csense , cap sensor can sense my touch, but when I cover a 1mm acrylic on the cap sensor, will not sense my touch.
so I want to know...
Hi ,
We are using BLE nano board as a connectivity board and mDot board as application chip which is running on mbed platform.Connection deatsils are same as described here...
Hi,
I am working in one application in which I need SAADC to sample two channels at 1ksps and 500 samples per seconds.
I am sending 1 and 2 to switch the sampling rate...
