Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
According to the documentation in infocenter there should be three soft devices for the nRF52832: 132, S212, S332. I downloaded the nRF5 SDK and I can only find the hex file...
Hi all,
Does anyone know the dimensions of the NRF51 dongle? I'm seeing 16mm x 28mm here but that doesn't seem right (might be the dimensions without the USB connector...
Hi,
Can any one suggest me how to program SoftDevice and Application program to nRF51288 BLE Motherboard using Keil 5? Please specify how much IROM1 and IRAM1 allocation...
I've studied the nRF OpenMesh for a couple of days, and could run the BLE_Gateway example among serval nRF51DK boards.
But now, I still don't have any feeling/concept about...
Hi, I’m looking for a data streaming solution to wirelessly transmit data over a short distance. Important points are:
unidirectional point-to-point transmission
...
Good morning,
my problem is that this module has a very short range.
The maximum range that I found was 4 meters.
Have you any solution for increasing this range?
Thanks...
Hi,
I saw several structs that you have in your library and I am curious as how you are forcing the alignment, since I want to do the same.
This is one of them:
typedef...
We are currently working on NRF52 DK.
I know that a Segger RTT is used to print the debug message using a Real Time Terminal(like TeraData or Hercules).
I know that...
Hi :)
I developed my Bluetooth app with MBed and the RedBear BLE nano module. My jumper wire installation connecting an stm32 with the module is working great and everybody...
Hello,
what is the initial output state of the comparator in single ended mode, if the input voltage is between the upper and lower threshold?
Is it undefined, always...
Hi,
I have a question regarding the nrf52 UARTE driver. I have the basics setup and working, I can send and receive data using the UARTE.
What I need to do now, is find...
Hi all,
Someone, please, can give me an information about programming a board nrf52832 using the pin SWDIO/SWCLK.
There is an application note that explain this topic...
