hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I would like to see output from NRF_LOG_DEBUG in the Rtt Viewer, to achieve that I changed (in sdk_config.h)
#define COMMON_CONFIG_LOG_LEVEL 4
#define NRF_LOG_BACKEND_SERIAL_USES_RTT...
Hi all!
These days I've developed a custom SAADC + UART program to fulfil my needs using the SAADC example in the SDK 11. I've tested it and all is working really fine...
I have 1 dongle and 2 NRF52DKs attached to my computer at the same time, when I am trying to use Keil to program just 1 board it seems like attempts to access all 3 my boards...
NFC examaples in SDK 12.2 and 13.0.0-1.alpha on nRF52832 (board PCA10040) may not work if HAL_NFC_FIELD_TIMER_PERIOD is set to a value higher than 255. HAL_NFC_FIELD_TIMER_PERIOD...
To my very limited knowledge, it has something to do with an "attribute table" of some sort. So you will have an init function, where you get to write all your attributes...
I use active scanning ，the observer will send a scan request when it hears and advertiser, and will listen for a scan response.I only see the scan event，but sent request and...
hello in nrf51 sdk, nordic has already ported freertos.
but if i want to port myself. can anyone tell me how to do it??
first i downloaded freertos from website. but then...
Hi,
I am new to nrf and trying to make some new services and characteristics for my device.
I followed the advertising , services and characteristics tutorial and was...
hello there i have ble_uart code . when i run on nrf51 dk and when i see it on mastercontrol pannel app. i got that type of screen shot!!
means when i write into characteristics...
NRF2460 is linked，I can transfer 3 byte data. But sometimes it is mute, not always.
Register I2SCNF_OUT bit6 is zero.
I am appreciate for your advices.
I have problem to start the wireshark with this plugin error. The last I checked the nordic_ble.dll file is there in the folder.
The procedure entry point new_creat_dissector...
Hi, I'm new to Nordic. I can't get 250Kbps working on the nRF24LE1. I'm using the enhanced shockburst examples in the nRFgo SDK (enhanced_shockburst_ptx_nrf2 and enhanced_shockburst_prx_nrf2...
Hi, I have an nRF24LE1 based sensor, transmitting to an nR24L01+ connected to an arduino (i know you don't supportit). I have LE1 to LE1 TX/RX working (as a test case). I...
Is there a way to disable (not use) the peer manager's whitelist without setting it to NULL? I'd like to be able to temporarily disable the whitelist without potentially losing...
