HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
I installed Bluetooth Developer Studio , (BDS), which appears to offer a way of setting up a custom profile without have to spend too much time on writing low level code....
Dear Everyone.
Hi, I develop nrf51822 with DK PCA10028. I have been optimizing the power consumption to some extent. But now I am very confused.
I use S110 softdevice...
Hello Everyone
We have a project using the Feather 32u4 BLE chip to communicate with an IONIC Application on Android.
And the huge problem is that i'm really really...
Hi,
I am interfacing HX711- 24 bit ADC for Weigh Scale to calculate weight which has
DOUT and PD_SCLK for Digital Output and Digital Input. I have the working Arduino code...
With Eddystone example in SDK12.0.0 I am trying to configure with nRF Beacon for Eddystone application but every time I change the URL " www.nordicsemi.com/" to something...
I use SPI connection according to the table .
I want to press the button 4 on tx (P.06) to transfer "hello", to write down the answer of rx(P.08) in the file on sd card in...
Hi
I'm using nrf51 to notify some data to an andriod device. I set the connection interval of my nrf51 program to 7.5ms. And I need to send 100 packets per second (20 bytes...
Hi Admin.
How can i calculate distance using RSSI. is there any existing method available? i tried statically(like 35-40=1m 40-45=2m) but i dont know actual method to get...
Hi all,
I am trying to add the iOSDFULibrary library to an existing Objective-c project via Cocoapods (Xcode 8.2.1 - target iOS 10).
I have followed the steps reported...
Hi
I've just done a few tests with the FDS system of the SDK12.2. My observation is, that the FDS doesn't properly use all assigned flash pages to reach a maximal lifetime...
Hi,
I am quite new to nRF51 development so please excuse me for my mistakes or not using right words if any. I have some code that fully works on the official nRF51 DK...
Iam using softdivice 110 and sdk 10.0.0, when i connect UART RX pin to TX of STN1110 the processor doesn't start until I remove connection between RX of nRF51822 and TX of...
Is this antenna pattern and design for our custom board is fine? we are using the nrf51822 with matching circuit.
Please put your valuable suggestion from your experience...
