Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi Nordic team,
This problem bothers me for a very long time. I cannot find the root cause. I used nRF51822 IC. It uses SDK11 with softdevice S130 and bootloader (but I...
Using nRF52 with SD 132 3.0.0.
Peer manager uses fstorage to store information.
I need to be able to specify the address range which fstorage can use.
Is there a configurable...
Hi,
I have problem with both functions sd_ble_gatts_value on central device.
It works on peripheral, because there is my characteristics definition.
Now I have to read...
Hello,
I'm developing a BLE Application where I use the peer manager. My Goal is to use direct advertising after disconnection if a device already has bonded. But every...
I am using the SAADC on the nRF52832, SDK12.2.0, with it set to 12 bits and low power mode. I have enabled five channels which I run blocking nrf_drv_saadc_sample_convert...
Dose this capture from the Nordic Specification means that to read bytes from SPI i need to send before. Each byte i send i get a byte!!!
MLy case i have read only sensor...
I am using the nrf52832 with the s132 for a project in which I have a frame with 24 bytes that need to be transmitted through BLE.
I have followed the tutorials and I have...
Hi,
First I'd like to salute the great work done by you Nordic people for those open source and hardware.
I just installed the SDK 10.0.0, S120, gcc-arm toolchain, configure...
Hello, I'm a beginner with the BLE technology and nRF52 is a good tool to start with it.
Currently, I have a setup that allows a Raspberry Pi and an nRF52 to communicate...
Hi. I have a problem with programming brand new chips nRF51422.
I have connected: Vcc (1, 12, 35, 36), Gnd (33,34,13), Swdio (23) Swdclk (24).
christal on the board:
...
I had downloading many versions SDK,from 10.0.0 to 12.2.0.But when I Program SoftDevice then download the examples,such as the path:
nRF5_SDK_12.0.0_12f24da\examples\ble_central_and_peripheral...
hi,all.
when i first time connect nRF52840PDK to PC, and open nRFgo Studio, but encounter this problem:
no device detected.
screenshot:
I click recover button many...
I want to send several packages in one interval from my iphone to 51822(s130).But the demo ble_app_uart can only receive 1 package per interval（ipone6，lightbule，writewithoutreponse...
I want printf the date and time when compiling code.
But I drag on this error:
SEGGER_RTT_printf("%s %s.\r\n", __DATE__,__TIME__);
compiler says:
It's strange...
Hi engineer,
I found that the SAADC current is increased after the SAADC function opened, then my processing method as below:
1,I close SAADC function after sampling...
