Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
I was looking the way to set different tx power values and also figuring out a small bug in the interface when you switch among payload models and payload length is >1.
Bug...
nrfgo_error.docx
Using nRFgo Studio as the interface I try to download the file “set_in _test_mode.hex” and get the error above.
What are the proper steps to get DTM...
I am trying to reset and halt the target nRF51822 under SWD protocol.
Could someone point out the register to achieve the same? I looked up the reference manual but couldn...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_uart" as reference.
As I've researching nRF51 with Central device,
it returns
Packet 0 : 020105 0c094e6f726469635f55415254...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
My setup is as follows
1 Gyroscope + Accelerometer
1 RTCC
1 SPI Flash device
I want to set up the PPI to periodically sample the MEMS devices and the RTCC...
Hello,
I am trying to remove the use of the frame pointers for bootloader_util.c because I am getting the error : "r7 cannot be used in asm here", but I only know how to...
I use nRF51822( BLE nano) central mode to connect annother BLE nano (ibeacon mode), then I call disconnection to the peer address. Sometime, the disconnection callback will...
hi,
i am trying to send data using ble_uart app.
in this app i am using timer difference to send data. when i am getting 1st data in uart event handler. when i am printing...
I would like to implement DFU OTA updates without the Master Control Panel, and I have a couple questions:
Is there example code for the client-side of the DFU service...
Our personal phones are set to auto-update iOS apps. Unfortunately our team all got the latest version of the NRF Toolbox app (v2.5) released on February 5th, 2016.
Previously...
hi,
i want to execute a block of code in which timer should start. and stop at end of the block. and the timing depends on manual interrupt. and restart again when the execution...
Im using a board that is not one of the officially supported nRF51822 boards. Im trying to get the ANCS example project to work, but It wont broadcast or even turn on the...
hi,
i want to append data before sending. i am using ble_uart example.
here suppose the data is available on uart buffer at 1data/sec. i want to sent some timer/counter...
SDK 4.0.0-2.alpha
When run garbage collection, sometimes invalid offset on new page is present.
Adding next string fix this.
m_swap_page.write_offset = FDS_PAGE_TAG_SIZE;...
