void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi. I'm using nRF51822 and SDK10.0.0, S130 for Central BLE.
I want multilink as Central.
As I know nRF51822 supports Max. 8 peripherals at the same time.
I can connect...
When using the sniffer to analyze GATT exchanges that use attributes > 20 bytes (which means L2CAP packets with fragmentation), the Wireshark tool does not show correct information...
hi.
i get a lot of information on Bluetooth and i want send it to 16 slave via ant.
what is the best way to send information over ant considering the speed of Bluetooth...
I have run into two SAADC issues on the nRF52832 using SDK v12.1.0. Any recommendations on how to fix them?
Issue 1:
When the Keil compiler optimization is turned up...
Hi,
Has anything changed in subject of one peripheral connecting to multiple central devices? All I need is little number (~3) of concurrent links with mobile phones.
I have been working on a custom board that uses a taiyo yoden EYSHJNZXZ module.
A tact switch is connected between P0.21 and GND.
I want to use this switch simple input...
Hi All!
I'm working a few weeks now with the NRF52 DK and having loads of fun!
Today I tried to make a central/scanner that scans for packages from a broadcaster. To...
I am trying to understand surface finishing of PCBs. In order to do so, can somebody tell me that what kind of surface finishing Nordic uses in boards like nrf51 - DK where...
Hello!
I am designing PCA10000 based PCB. Unfortunately my manufacturer can't make PCB using prepegs and cores that used in PCA10000 (4.4 and 4.8). They can make using 4...
Hi Nordic
After download SDK12.1.0, I want to extend DFU service in my application.But i find it different with the pervious versions.
For example, i can know how to...
Hi,
I have just started a new project in uVision, using the ble-app-template from the peripheral examples. its running on a custom PCB, with no 32Khz XTAL, and i have changed...
The user manual only tells information of pins , active low such things of led on nRF52832 Dk. There is no detail information of components on nRF 52832 DK board. So, can...
After reading the FAQ on DFU I still do not understand how the bootloader and SD DFU are performed so that a failure during the upgrade does not brick the device (see answer...
Hi,
I have some queries about ESB RF Communications.
1.The address : is it possible change RF communication to one node(Tx) to multiple nodes(Rx). If Yes, Where can...
