I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
What happens when the bootloader settings page is not programmed with the bootloader to the device?
This page is automatically created and all the versions set to 0? Or...
Hi,
I use a nRF52832 on pca10040 with s132 as RX
and an arduino uno with a nRF2401L+ as TX
The nRF52 is a BLE NUS peripheral and can receive ESB packet with timeslot...
Hi,
I am using SDK 10 and Dev kit nrf51422 and used \nRF51_SDK_10.0.0_dc26b5e\examples\dfu\bootloader\pca10028\dual_bank_ble_s110\arm5_no_packs
to make the bootloader...
Hi everyone,
I am working with PCA10000 dongles with S110 and S120 softdevices. The connection parameters in both master and slave are
define MIN_CONN_INTERVAL MSEC_TO_UNITS...
Hi,
I plan to immigrate from NRF51822 to NRF52832 soon. My SDK is Version8.1.1 on NRF51822 now.Can you tell me which version of SDK should I choose to start this work, please...
Hi I am presently working on MPU92/65 sensor interfacing with TWI/I2C.
i am using nRF51822 EK with soft device s130_nRF51_2.0.0(id:0x0080) and nRF5 SDK v11.0.0 and keil...
Hi,
I want to get the RSSI for each peripheral that is connected to an nRF52 when it is operating as a multi-link central to multiple peripherals. Helpful hints? Sample code...
Hey. I want to wake my s110 device every 30-40 second to advertise for a few seconds only. Is there an example on this or if someone could guide me in the right direction...
Hi all,
I need to using NRF51822 as a clock: second, min, hour, date.... I know I only use RTC as a timer 1s. When NRF51822 power off then time was lost. So, I must be...
Hello,
I have some problem with a specific phone. I try to connect with the nrf52832 using samsung S3 with android version 5.1, the connection takes 20 - 50 seconds and...
Hi,
I am very new to nrf51822 controller. I Used STM32 cortex controller's.
I want to know basic hardware which are the require to start nrf51822 working and programming...
The example nRF51-DK gerbers have solder mask on the PCB antenna. But for the nRF24L01+ EK gerbers, the PCB antenna has the solder mask removed partially, along the length...
