This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
hi,
I am working with nr52832 and SDK 12.1.
I have referred the RNG example based on which I have integrated that code section in my custom application:
rng_generate...
I'm trying to accomplish a communication from the nrf24LE1 to the nrf24L01+. The nrf24L01+ is hooked up to an Arduino UNO. The nrf24LE1 is flashed with the "enhanced_shockburst_ptx_nrf24le1...
6.1.4 Erasing a page in code region 1
When erase is enabled, the NVM can be erased page by page using the ERASEPAGE register or the ERASEPCR1
register. After erasing a NVM...
Hello,
I was testing BLE Heart Rate Collector Example with two nRF52832 devices, one was programmed with ble_app_hrs_c as a BLE central role, and the other was programmed...
Hello everyone,
I have very pesky bug that is leaving me in fits. I have a feeling it is a timing issue, but I am not sure at this point. Here is my issue, and I would...
Hi Devzone.
I've taken the ble_app_hrs example,
and then added the example code from the PWM Driver example.
The PWM module is mostly functional,
however I have a...
Hi,
I'm trying to build a SPI Slave <-> BLE bridge, so that everything received over SPI bus is forwarded on BLE and vice versa. In order for the reverse direction to work...
Hello,
i think this is simple question, but nowhere i can find answer. Is nRF52840 preview development kit (PCA10056) contains built in nrf52840 microcontroller or i need...
I am going through the BLE Central tutorial and am a bit confused by the APPL_LOG function calls, from what I could understand it should give messages on serial port, like...
Hello, I have nRF51822 Beacon Kit (pca200006) and nrf51 dk board (pca100028)
I had an impression I could flash beacon and upload new files using nrf51 dk board as jlink over...
I am using IOS nRF Toolbox 4.2 DFU function on nRF51 DK PCA10028. I followed the tutorial here .
Use nRFgo Studio to erase all.
Use nRFgo Studio to program...
We have an nRF51822 peripheral device that is bonded with one and only one central. The central is always an iOS or Android phone running our app, which is scanning at "low...
In the BLE advertising library, in SDK 11, is the timeout for directed slow advertising specified in seconds, or in number of tries?
Seconds would be more consistent with...
Hi All,
I have got a project running on an nRF51422 QFAC, using the lastest SDK.
I am having some problems with the app_timers, i am able to create and start them, and...
