Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hello,
I am trying to implement a Heart Rate Monitor Interface (HRMI) board with my nRF52, using the TWI_sensor example from SDK 12.2. I am running into trouble Writing...
Setting up an example of the problem
As I promised in this thread , I have been testing out the ADC on the nRF51822 and trying to see how quickly I can sample per minute...
I'm using FDS in SDK 11.0.0 on a nRF52832. I was having some trouble with freeing flash storage and after doing some research I came across this post and I applied this patch...
Hello,
There is a bug in pstorage.c from SDK which can cause that module to fail to complete a flash operation. The problem is that the pstorage_sys_evt_handler function...
The product spec says "This event will also be generated if the supply voltage is already below VPOF at the time the POF is enabled" but it seems like the event is not generated...
I have a BLE device that is using Nordic SDK 8.1 and uses PWM to control an LED. Now I want to turn the led off with PWM. To do this I set the duty cycle to 0 and printed...
Hi,
I'm working on nrf51822 with soft device s130. I'm trying to send a data packets from the nRF51822 over BLE to an android device.
I want to know how much data...
Hi!
I try to create a custom service. To do that I copied the ble_bas service and followed this guide.
You can see my init function here:
#define APP_UUID {{ 0xC0...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 as central and peripheral.
Q1. What's "sd_ble_uuid_vs_add" function? is it for setting service UUID?
Q2. If Q1 yes, how to change...
I was reading a review of this product from a 3th party and they was claiming that a disadvantage about using this chip is that "Some peripherals and resources are not available...
SDK: 13.0.0.0-1.alpha
example ： ble_app_hrs_freertos
I am developing a product, referring to the “ble_app_hrs_freertos” example, when I tested my functions found a serious...
I've just tried to update the mbed firmware on an nRF52-DK to version 0219, and have hit some problems. Firstly, after dragging the .bin file into the Bootloader drive, my...
I've had a sequene of problems attempting to install the power profiler software on my Lenovo T420 Win7 64 bit machine.
First Issue
When attempting to run the python_packages...
I would like to pick up audio signal with a microphone for ex. AKU340, then use audio codec to digitize it, then save the output in a SD card connected to the nrf52, reading...
