Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
I'm trying to connect to a Raspberry Pi from an nRF52832 via BLE Central mode. The Pi is running a node.js app (via bleno) and I can connect and communicate with it...
i m using pca10028.. with gcc tool chain setup with sdk 8 in windows.....am run one ble_uart example and after 180 second my device goes to sleep.. and second one that i have...
I'm using the SAADC of an nRF52832. I'd like to reduce the error of my measurements from the nominal +/-3%. I'm calling the NRF_SAADC_TASK_CALIBRATEOFFSET periodically to...
Hi,
I am trying to use nrfutil to generate my verification key.
However in the bootloader the key has this format
__ALIGN(4) const uint8_t pk[64] =
{
0x6e, 0x76...
Hello,
I am trying to update my bootloader using DFU and I am running into a few issues. I have successfully flashed and tested my current bootloader on my board and everything...
I am using the nRF51822 in an application where I want to run the UART as fast as possible to communicate with a host processor. I have been able to get reliable communication...
I am trying to create a package file to use with the DFU on my design.
I followed the instructions for getting nrfutil latest version built and was able to generate a private...
I'm using an NRF8001 with an ATMEL ATMEGA 328P (the microcontroller from an Arduino). I need the microcontroller to go to sleep, but still allow the BLE chip to advertise...
Hi,
for development i am using gcc and makefile on osx.
I wanted to automate my makefile with the possibility to upload directly the hex file to my nrf52 devboard.
...
I'm using PPI to trigger a gpio high after a given delay from 4.00 ms to 8.00 ms. I need to be accurate up to .01 ms but i'm seeing some jitter in the actual delay vs given...
Hi,
documentation for NRF_LOG_RAW_INFO state that it is:
A macro for logging a formatted string without any prefix or timestamp.
But when I use next code snippet...
Hi
After building ble_app_uart in Nordic SDK with board pca10028 it gives some warning like
/usr/lib/gcc/arm-none-eabi/4.9.3/../../../arm-none-eabi/bin/ld: warning...
hello sir, i m using gcc tool chain setup in windows with sdk12 in pca10028... so can i useexample->peripharal-> timer example same as rtc ... i mean sleep condition same...
I would like to use the flashwrite function to store some data in the flash. There is an example in SDK 11.0/peripheral.
But I have a few questions about the example: ...
