Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Is it possible to put the nRF52 into recieve only mode (say through direct test mode) so that the input impedance can be measured using a VNA? Is the input impedance of the...
When I initialize PPI after timer1 has been initialized I get a fatal error (and reset).
Code:
const nrf_drv_timer_t timer1 = NRF_DRV_TIMER_INSTANCE(1);
nrf_ppi_channel_t...
Hello,
we were measuring sleep modes and it consumes around 1.3uA which is correct.
But when we needed to be woken up on edge we found out it consumes extra 8uA! Are you...
Are there any nRF51 demo firmware implementing paring function that the central and peripheral devices will connect automatically without user interaction when they come ...
i am working using NRF52, s132, sdk11, freertos.
for fft , i used "arm_rfft_fast_f32(...)" in cmsis-dsp library.
and i inserted a fpu interrupt.
NVIC_SetPriority...
Hi.
I'm using PCA10040.
I'm trying to control GPIO.
But I can't control PIN 09, 10.
Let me show you my source code.
int main(void)
{
/* Configure LED-pins as outputs...
Hello!
I have encountered an interesting issue:
When I use compiler flags (GCC CFLAGS) -Os or -O0 together with -flto the pstorage function pstorage_block_identifier_get...
After I combined the Timer example and ble_app_uart, the program is hanged at below function when init the timer. Please tell me why
__STATIC_INLINE void nrf_timer_event_clear...
I need to turn off a GPIO after 8 hours of it being triggered.
I was reading about changing the prescaler to allot for 8 hours. I did the calculations and came up with a...
I have purchased a red bear lab ble nano board with nrf51822 and a PICTAIL board with microchip RN4020 chip. i have set Tx power 4 for both boards. The rssi value shown in...
This may just be a preference or architecturing question but I thought I'd ask in case there was anything I'm not thinking of, or benefit of one or the other.
I have 2...
Hello,i am find an interesting phenomenon recently.I have a Nordic 5182 device(role as peripheral) and bonded to an iOS device(role as master),when i put the iOS device near...
I'm wondering, is it possible? This is what I think it will be like if it were going to be implemented:
Acquire the firmware from a host somewhere.
Since the payload...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
