I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
When one host and one device,the through can be 16KBps。But,when one host and two device ,the Max throughput is only 6KBps。Can you tell me Why ?????And Can you tell me the...
I use keil4. When the code size less than 15297bytes is ok. I will cause error when the code size bigger than 15297bytes.
Something must config in keil4?
Thanks~
I'm trying to listen to a bluetooth low energy connection between a smart bracelet and my smartphone. In Wireshark 1.10.1 I only can see the Advertising Indicators. As soon...
We are able to run both these services (experimental buttonless DFU and experimental app ble blinky) individually in Eclipse GCC, SDK 12. However, when both of the services...
I am intended to integrate the Nordic SoC nRF52832 in our PCB to generate a PWM.
However, I could not understand the difference between the following:
topicSchematic QFAA...
Hi to everyone, i have the mpu6050 code and i have to change it with parameters of adxl345.
i have this definitions:
#define ADDRESS_WHO_AM_I (0x75U) //!< WHO_AM_I register...
Hi, I am trying to connect a peripheral device which in this case is a BLE device called DELTA and I am trying to connect it to a central device which is the NRF52 board....
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
In nRF5_SDK_12.1.0_0d23e2a in file: ...\components\softdevice\common\softdevice_handler\ant_stack_handler_types.h In lines 30-32 inside #ifdef ANT_STACK_SUPPORT_REQD is preprocessor...
Hi ,
I have nRF51822 beacon and J-Link LITE and i am using nRFgo studio setup .I am trying to flash the hex file in to the beacon using nRfgo studio.The beacon has two...
Hello!
The DEC2 pin is connected to an N.C. capacitor C6 in the newest refreance layout and the nRF52 DK layout. So does it mean I can just left it DNC like the 44th pin...
Hi,
I have a custom board of nrf51822 with no external crystal, neither 16 Mhz nor 32Khz. I am trying to use uart and app timers from SDK11 but when I start any app timer...
I'm in a situation similar to the one described in this question:
devzone.nordicsemi.com/.../
The company performing the test ask me to provide a device that can switch...
