Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hi,
I'am tring to test the dfu by secure bootloader.I had done all steps like: Test the BLE Secure DFU Bootloader application by performing the following steps .But I found...
I am implementing an SPI master to communicate with an accelerometer using the SPI HAL directly. My chip is marked nrf51822QFACA11609AC. I have implemented blocking functions...
Hi,
When the UART is configured to use FIFO , i use the UNUSED_VARIABLE(app_uart_get(rxdata));
to read a buffer from FIFO.
how can i also receive a number of bytes...
Hi,
I want to do this cycle with GPIO without interrupting it on NRF51 with BLE softdevice:
PIN1 to HIGH level
read value of PIN2
PIN1 to LOW level
Repeat...
Hello, I'd like to do directed avertising to a central which has a random private resolvable address. My idea: both devices share a pre-defined IRK so the peripheral can compute...
I tried, but it does not work.
for(int y=0;y<100000;y++)
{
if(nrf_uart_event_check(NRF_UART0, NRF_UART_EVENT_TXDRDY))
{
nrf_uart_event_clear(NRF_UART0, NRF_UART_EVENT_TXDRDY...
Hi,
We have a little issue that we at the moment need to cycle power on v3 nRF51822 after DFU.
We have determined the the reason has something to do with the whole complicated...
I attempted to add spi_master as below, but I am in trouble with link error.
If anyone knows the cause, please tell me.
*** Using Compiler 'V5.06 update 4 (build 422)...
I'm working on a project based on the ble_app_uart_c central example in SDK 12.1. I'm polling the RSSI of a Nordic beacon using sd_ble_gap_rssi_get(), and the fastest update...
I want to handle 3.3v in nrf52832.
NRF_GPIO_PIN_S0S1 -> NRF_GPIO_PIN_H0S1
Can this be this way?
If not, what should I do?
Also, Can the PWM output to 3.3v?
Hi, I use PCA10040 v1.1 and SDK12.1. My desktop environment is Windows 7 64bit.
As far as I know, the J-Link Edu cannot be used for commercial usage.
I so bought...
Hi there,
We've had our own custom controller made, based on nRF52 (Rigado BMD-300 module).
In the last half of January we'll have a baseline firmware working, but we...
Hi, sending a data packet, then sleeping (memory retention mode), then sending another identical packet causes the receiver to send back an ACK for the first and trigger NRF_ISR...
