We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I am using the nrf52832 with its Development kit to transmit trough UART to the PC a frame with 20 bytes, I have configured the port to 1MBoudRate. I have enable the flow...
I spent some time trying to work out why generating a private/public keypair in my application with the ECC module was failing due to an 'internal error' and had to eventually...
Hi,
In 868 Mhz band NRF905 supports frequencies 862.8Mhz, 868.2Mhz, 868.4Mhz and 868.8Mhz. The datasheet shows mapping of those frequencies to CH_NO.
In India only 865Mhz...
Hi,
I am currently working with two nrf52 boards in a serialized configuration.
I wanted to add the PA and LNA pin toogle on the connectivity chip.
As the gpio can't...
sorry, i tried "Getting started with the nRF5 development kit" tuturial about 3 hour.
but still not working for me.
stock at begining.
I downloaded nRF5 SDK 11
and...
Hello,
We are using nRF52 in serialization mode.
In the nRF52 connectivity chip side, we are using the example 'ble_central_and_peripheral'.
In the application chip,...
I would like to use the nRF52840 for 802.15.4 but it is rather vague in the OPS as to how to do this. I can figure some of it out but not other parts.
It mentions "assisted...
Hi All ,
Is there any sample application to have a list of available peripherals(Like displaying in mobile when we scan) , for a given interval ?
If not please suggest...
Hi,
i am trying to update OTA application zip file size 112kb but it become failed and showing upload failed: REMOTE DFU DATA SIZE EXCEEDS LIMIT , But if i am flash small...
I am developing a battery powered application using the Nordic UART Service.I intend to use the ble_uart peripheral example as it is , modifying it as per the application...
Dear Nordic Team,
Thanks for supporting.
Currently i am working with MMA8453 accelerometer . I already interface with nRF51422 using TWI it is working fine. The sensor...
This might be small problem, but i am not able to fix it.
i am working with nRF52 DK .i had created new project, in which i am using spim0 and spim1, also want to use ble_app_uart...
hi,
I am using 51822 PCA10000 dongle based nRF BLE sniffer to analyse packet exachange between my product and central devices. When I set filter to the mac address of my...
Where can I find discriptors handle other than cccd, sccd?
I already know sd_ble_gatts_characteristic_add() return cccd, sccd handles in m_nus->service_handle->cccd_handle...
Hi.
I'm using nRF51822AC, SDK12.2.0 as Central.
Q1. Is there any function to know regarding it is scanning or not?
Q2. As your example "ble_app_multilink_central",...
