In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Now I work on designing a product, which is implemented by sending LMP commands to a bluetooth device with nrf51822. Unfortunately, nrf51822 liberary could not provide the...
Hello All
I'm newbe for this device. Now my customer asking multiple offline programming IC NRF51822-QFAC-R. But I'm not sure the device can support parallel programming...
Hello,
has anyone done some good testing on the connection quality between multiple nRF51 chipsets running on the S130 SoftDevice? (Using all four connections, 3 as Central...
I'm trying to merge 'ble_app_uart' and 'twi_sensor' example.
I developed twi function in 'twi_sensor' example. I add 'ble_app_uart' example file 'nrf_drv_twi.c'
and also...
nrf51822_sleep.txt
Currently i running nordic code in Arduino IDE through the library from RedbearLab : github.com/.../nRF51822-Arduino and I facing a problem in sleeping...
Hi, can anyone explain to me about this example in this link with details :
github.com/.../main.c
I'm a newbie in nordic and i found it difficult to understand this example...
I install
gcc-arm-none-eabi-4_9-2015q3-20150921-win32
make-3.81
coreutils-5.3.0
and setup the PATH in windows
then i enter CMD mode make some command to...
I am using the LFCLK RC oscillator, 8000ms calibration interval.
Is it possible to read from some register the resulting calibration value for the LFCLK RC oscillator?
Now I work on designing a product, which is implemented by sending LMP commands to a bluetooth device with nrf51822. Unfortunately, nrf51822 liberary could not provide the...
Hello,
measuring ADC signal on P0.26/AIN0/XL2 and P0.27/AIN1/XL1 doesn't work (I get constant value from the ADC not reflecting actual voltage on the pin). AIN2 - AIN7 seem...
I need to send a disconnect command from the app layer. I've seen a few other posts that say to use uint32_t sd_ble_gap_disconnect. One post had this line of code as an answer...
I am using the RBC mesh in a networking product using the nRF51422. We would like to turn the mesh on and off at selected times, say once per hour for a minute or two. I know...
Hey,
I have been trying to set up wdt for my application which services some interrupts once in a while and advertises continuously. I put the nrf to sleep using sd_app_evt_wait...
Hello,
I'm trying to read voltage signals from a sensor using internal ADC and send them OTA. For now, my codes seems to work, but the only problem with my codes is it...
