I'm running into this issue quite often where I have a Build failure. I'm sure to others the way to troubleshoot what the issue is may be obvious, but being fairly new to...
Hi,
I cannot bond to NRF5340DK running the `peripheral_ancs_client` sample if external oscillator configuration is disabled (thus using synthesized from HFCLK).
Environment...
Hi,
We are working on nRF5340 with TF-M enabled and iOS application.
What we are observing is the peripheral device MTU TX and RX are configured to 512 bytes whereas the...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hello All,
I have nrf9610 Develoment Kit on my side:
mfw_nrf9160_1.3.5
Using nrfutil-device core version: 7.13.0
Using nrfutil-device version: 2.1.1
...
I am developing an MQTT client application with NRF9160, trying to connect to a Mosquitto broker using TLS with three certificates. However, I am encountering an SSL version...
hi support team,
in 9161dk, when we need to program external flash, we need to config board with nrf connect, may i ask what's this? and if i need to consider power consumption...
I am working on nrf52832 based custom board and I want system off sleep and wakeup using GPIO pin state change. For that I have configured MCU standby timeout in sdk_config...
Hi, We have tested beacon sample in our custom board. Build with nrf7002dk_nrf5340_cpuapp_ns board config. Facing below issue but the same build is working fine in nrf7002...
It seems hostap has a bug. This line:
https://github.com/nrfconnect/sdk-nrf/blob/4e9436d1076a362adf168e6a8878a8b32b8bff4d/modules/hostap/src/supp_api.c#L312C2-L312C78
...
I have a thingy91 device and want to implement the following requirements.
Expectation:
NRF9160 should remain in deep sleep mode and on the button click event do the...
I am developing firmware for a BLE peripheral using ncs v2.6.1.
In addition to using the libraries introduced in nRF Connect SDK Fundamentals and BLE Fundamentals on DevAcademy...
Hi,
I am considering to build a line of products using the nRF 5340 product and I am considering the options to perform FOTA.
So far the option I learned from the Intermediate...
1. What could be the reason why streaming is not synchronized even though the connection is established?
2. Where in the source is the important information for connecting...
Hi there
I want to measure the accuracy of the 32.768 kHz oscillator connected to a nRF5340
I have tried a lot of other devzone tickets, but most of them are too old or...
Hi ,
nRF52832 using pairing connection with Android phone,after repeatedly disconnect and re-connect ,after several minutes will maybe make the phone's bondibng information...
Hi,
I have now sync the transmit of nrf IC to communicate with tas2781 audio amplifier. at this moment I'm working on the feedback measurement read of the I/V measurement...
Hello, nordic team
I have encountered unusually high power consumption in a simple GPIO edge interrupt application running on a custom nRF9160 board. The application is...
Hi there, I have an nrf52840 DK and I wonder if it is possible to upgrade my own application firmware via fwupd tool on Ubuntu.I want to successfully upgrade the development...
Hi Support Team
We want to implement multiple beacons in one chip, for example, one beacon carry battery level and the other carry sensor data, and we want the beacon...
Hi everyone,
I fill a bit surprise but I don't understand who the speed of the gps is working :
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/applications...