i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
Hello ,
We are attempting to use the QSPI driver with an MX25 with 2 i/o lines instead of 4, essential SB 10 and 15 on the nrf52840 DK have been cut. However I am not...
Since the APP CPU memory is mapped at 0x2000.0000 in the perspective of the NET CPU, we understand that r/w access is possible for data. Is it possible for the NET CPU to...
I have a vendor model bt_mesh_model_op defined as follows
const struct bt_mesh_model_op _admin_model_ops [] = {
{ BT_MESH_MODEL_OP_3 ( OPCODE_SET_UNACK , VENDOR_ CID...
After several months of attempts, I was finally able to load, build, and flash the code from multi-NUS-master.zip using the VS version of nRF Connect, onto the nRF52840 DevKit...
Hello Nordic support team,
We are now creating a BLE central device which is part of a medical equipment.
The BLE communication works fine, but we want to add a BLE...
i'm writing a code for mic without using i2s because that mic will generate digital pdm signal.
i saw there is no solid code for low level driver or hard coding
Hi I want to set up a simple uarte communication between a NRF52832 and a faulhaber mcdc 3002s motion controller using the libuarte. I have max3232 logic converter in between...
Hello,
while migrating our FruityMesh framework to SDK17 I went through all SDK and SoftDevice release notes and migration documents and saw the following:
Now, to...
Hi Nordic Team,
Few questions about Power supply supervisor block of nRF52810. My device's supply volage (VDD) is 2 volt. I have enabled POFCON and the handler is getting...
Hello. I am designing an application where the goal is to send a notification, sleep for 1 second, send another etc.
To do this I used the application designed in this guide...
Hello,
I'm working on KX132-1211 accelerometer with nRF52832 and am using I2C(TWI) protocol. For that I need to create driver files even I was contact with manufactural...
Hi,
I have a model_handler.c which builds fine, but the moment I change it to model_handler.cpp, I get build errors saying "duplicate descriptor is not allowed". I am struggling...
Hi, There is code for vendor model element creation in nCS provided Chat client sample, as in below:
This works fine in "model_handler.c",
But when I import the same...
nrfjprog checks the target for 0xFFFFFF before attempting to write.
It should be successful not only if attempt to write the same value as is already present but also
...
Hei, jeg evalurere et Reinsdyr projekt der 30 Reinsdyr skal løper inne i en binge, er det mulig å motta kun beacon fra BLE taggen i nRFAPP fra de 30, hva er max antall når...
