Hi Nordic Team,
We are experiencing an intermittent Buttonless Secure DFU over BLE issue on our custom hardware based on the Raytac MDBT50Q-1MV2 (nRF52840) module.
Software...
I have been using a NRF52-DK board to develop a BTle solution for the past week. Today, midway through a debug session, the board vanished from my BT interfaces. It also no...
The nRF54L15 Product Specification lists the following PDM feature:
"8 kHz, 16 kHz, 32 kHz, or 48 kHz output sample rate" "Supports digital microphone clocks at 768 kHz...
Hello,
I have just downloaded the NRF52840 Reference Altium Library.
I have noticed that the step file for the component is not symmetrical about the origin.
If I measure...
We're implementing a PAwR (Periodic Advertising with Responses) based onboarding flow for a large fleet of devices (target: 200+ nodes, eventually scaling to 1000s) and are...
Hello Nordic Support Team,
We are using a Fanstel module that integrates the nRF5340 BLE SoC and nRF7002 Wi-Fi companion IC in a single module.
We have manufactured approximately...
Hello everyone, I'm working on a long-distance communication application (>50m).
My hardware is nRF52840, PA/LNA: RFX2401C, ceramic antenna: AN9520-245.
I've achieved...
Hello, Is it possible to add the remote provisioning functionality with the interactive PyAci serial library? We are developing a desktop application to do configuration and...
Hello.
It is developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I'm trying to characteristically add BLE_UUID_GAP_CHARACTERISTIC_DEVICE_NAME and...
Hi!
I'm developing a small central BLE software, everything works well, please assume that I have correclty instantiated a connection, did the service and characteristic...
Hi,
I have looked around the internet and am trying to understand the ble security options. I cannot understand the correct approach to take for our application.
Our situation...
Hi,
How interrupt is working in nrf saac driver? I can see that it is already code is present in the adc_nrf_saac.c
static int init_saadc ( const struct device...
Hello,
I was wondering if it is possible to port older projects built using the now deprecated Nordic Thingy:52 SDK ( https://github.com/NordicSemiconductor/Nordic-Thingy52...
Hi,
As a university we bought several NRF51422 dongles to sniff BLE traffic
Following the installation instruction here: https://infocenter.nordicsemi.com/index.jsp?topic...
Hello,
I am new in nordic previously I was working on Cypress controllers. I am trying to put the device in System ON Low power mode.
I have tried the below functions...
Hi,
I am working on a project using BT Mesh and I am evaluating a prototype using the nrf52840. I am not working with the mesh-SDK, because I am using zephyr. I am working...
Hi, I have a University group project which required us to build software on Android devices. Basically, this project requires us to build software based on BLE Mesh between...
Hello,
I want to communicate one card nrf5340dk with 2 same card in using 'central_uart' and 'peripheral_uart' samples.
I have succeeded to establish the connection and...
Hi,
We have a new product and are looking into OOB pairing for authentication and encryption. All the information about OOB flows back to NFC pairing, but that is not what...
Hi
I am working on an application that uses extended periodic advertising feature of BLE 5. In this sample (periodic sync):
https://github.com/nrfconnect/sdk-zephyr...
Hello nordic. I have several SPI peripherals connected to the nRF9160. I'm using the PPK2 in ampere mode. Does this then also measure the additional current drawn by the SPI...
