The NTN AT command guide documents a "Signal quality check" option for performing a pre-check before attempting to re-attach to the Skylo network:
https://docs.nordicsemi...
Hello,
I am trying to flash and debug a custom board using the Raytac MDBT42Q-512KV2 that uses the nRF52832 module mounted. I tried this using the jlink plus and the nRF52...
I have a similar question to this , however it's for the nRF54 family. Can I route similar the SWD signals out through unused pins/balls on a BGA? In this case, I'd route...
Hi DevZone,
I am currently working on a project that uses MCUboot (DFU over BLE) on the CPUAPP core together with a custom FLPR application.
I successfully got this working...
Hi Nordic,
We are building a custom board using the nRF9151 LACA.
We see a back-powering issue between the GNSS antenna bias rail and VDD_GPIO.
Setup:
VDD_GPIO...
nRF54L15 FOTA Failure:
MCUboot reports magic=bad on Slot 0 and magic=unset on Slot 1 using NSIB + MCUboot + TF-M with Pure DTS Partitioning
Description
I am implementing...
Hello,
We have a project currently using NCS v3.2.3. We delivered the first production series of 50 units already, with the NSIB from this NCS version. We use the NSIB with...
I have been using the Nordic Power Profiler Kit 2 with the Nordic Power Profiler application for reading current measurements on an external device and have been saving/exporting...
I recently updated to nRF Connect SDK v1.8.0 from v1.5.0 and am encountering a new error with the same code. The error occurs when I call bt_le_ext_adv_set_data. My advertising...
This is in regards to my last post here: https://devzone.nordicsemi.com/f/nordic-q-a/84016/switching-between-two-applications-using-nrf5-sdk
I am using FreeRTOS.
Both...
During the development process, I had no trouble bonding with the rfConnect (current version from the website). After many changes to code, I got it to bond one time and deleted...
Hi,
Is it possible to use "nearby fast pair" technology on the nRF52833 platform? are there any examples of the use of this technology?
Best regards,
KaEd1705
Hi, I am using libuartes and when I receive text from other device my nrf52833 will respone "textAT1_Uart1". But I can not free them (using &libuartes1 because I'm using 2...
In nordic ncs zephyr use Nordi ble controller (SDC) else in zephyr mainline will use a software version of the controller that use LLL (BLE CONTROLLER).
Il possible to know...
I'm trying to create a minimal executable that has a structure placed at a specific address in flash. It looks like CONFIG_CODE_DATA_RELOCATION is needed to do this. However...
Hello,
we are trying to get the uart secure bootloader running on the nRF52820. When linking we receive the error message that RTC1_IRQHandler is defined multiple times...
For an upcoming product based on the nRF52811 chipset I wanted to prepare for the arrival of the new AP-Protect variant of that chipset and have a unified firmware that runs...
I'm using SDK12 and SDK15 on nRF52832 and nRF52840 (peripheral and central), although this would appear to be an issue with other devices too.
If I connect with NRF Connect...
Potentially related to : nRF Connect v3.9.3 does not detect external j Link programmer - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com) , but I don't see the...
Hi,there:
I was used 2 52832 board to run the linght switch server/client examples to test message communication. I add the mesh events handle like this:
Then run the...
Hi,
I am trying to transfer a dataset of over 100k, via a custom service from a peripheral device.
There are many posts in this forum that describe ways to do this but...
Hi,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK_v5.0. The Client sends unacknowledged messages to the Server ( APP_UNACK_MSG_REPEAT_COUNT...
