Hello,
I am trying to flash and debug a custom board using the Raytac MDBT42Q-512KV2 that uses the nRF52832 module mounted. I tried this using the jlink plus and the nRF52...
I have a similar question to this , however it's for the nRF54 family. Can I route similar the SWD signals out through unused pins/balls on a BGA? In this case, I'd route...
Hi DevZone,
I am currently working on a project that uses MCUboot (DFU over BLE) on the CPUAPP core together with a custom FLPR application.
I successfully got this working...
Hi Nordic,
We are building a custom board using the nRF9151 LACA.
We see a back-powering issue between the GNSS antenna bias rail and VDD_GPIO.
Setup:
VDD_GPIO...
nRF54L15 FOTA Failure:
MCUboot reports magic=bad on Slot 0 and magic=unset on Slot 1 using NSIB + MCUboot + TF-M with Pure DTS Partitioning
Description
I am implementing...
Hello,
We have a project currently using NCS v3.2.3. We delivered the first production series of 50 units already, with the NSIB from this NCS version. We use the NSIB with...
May I ask if the nRF54L15 comes with a default state when shipped, or is it blank? Also, what’s the GPIO status? I’m asking because it will connect with the AP, and I’m worried...
Can an iBasis sim card be activated without being in a device (nRF9160dk or Thingy:91).
I have two sim cards and neither will activate.
Most of the time after entering...
aoa rx hardware: nrf52833DK
aoa tx hardware: my test nrf52833 board
my test nrf52833 board download "direction_finding_connectionless_tx", use " overlay-aoa.conf"
nrf52833DK...
We are currently in the process of looking into the Bluetooth certification as part of a Homekit accessory, and the documentation raised some questions:
the QDID for the...
Hi,
I'm new to ble.
In order to better understand what is going on, on a packet leveI got a packet sniffer.
I found a device that uses a nordic chip, and am trying...
Hi, I am trying to develop an nCS application with serial flash interface, I am using an nRF52833dk & I observed that under the nCS path "v1.8.0\zephyr\drivers\flash" There...
Please guide what changes are to be done for the Light bulb example to be run in 52840 Dongle?
I am using VS Code and built the Build Configuration using the Dongle configuration...
Hello.
I am yoo at korea.
We will connect OLED with QSPI and Driver IC supports SLOWREAD.
- 8bit (Opcode: 0x03) + 24bit (Addr) + 8bit (Read value: Mandatory) + 8bit...
Hello.
I have question for QSPI OPCODE.
According to "nRF52840_PS_V1.5", WREN optional at "the custom Instruction".
- using function: nrf_drv_qspi_cinstr_xfer
...
Hi, I'm trying to use light_lightness example , and button_event_handler didn't work.
Error message is
"multiple definition of "GPIOTE_IRQHandler" "
because I added...
Hi, I'm using nRF52 DK. I'm following tutorial links 1 , 2 and 3 to learn how to add BLE OTA DFU to the example project ble_app_uart.
Step 1
Following the above links...
Dear ,
I am currently testing the UART peripheral on nRF52832 and nRF52840 using nRF Connect SDK.
Basically, I have a sensor that continues sending out data via uart and...
I'm trying to build the pc-ble-driver ( https://github.com/NordicSemiconductor/pc-ble-driver ) to be able to use the nRF52840 as a receiver for a thermometer. See https:/...
I have a custom board with NRF52833 that I'm unable to flash or communicate with using JLinkGDBServer. I was hoping for some help understanding the errors seen in this log...
Hello Nordic team!
I had a post where I verified the answer by misclick: https://devzone.nordicsemi.com/f/nordic-q-a/83749/nrf52-dk-as-central-to-discover-services-on...
Hello
I'm using nRF5340 DK with nRF Connect SDK 1.5.0 and SES IDE and I want to change the PHYs and TX power of the peripheral_uart sample ( v1.5.0\nrf\samples\bluetooth...
