I am working with the NRF52832 DK with a Tag-Connect 3 prong cable attached to the debug port.
I have found a bug that has so far been 100% reproducible. It already happened...
Hi team,
I recently purchased some nRF54LM20A units and I am currently working on interfacing them with a W5500 Ethernet module over SPI. However, I am facing difficulties...
I just programmed 2 Boards.
One Peripheral advertising with 1m Phy and other peripheral with s8 codded phy.
Using NRF connect app and wire sharc I made sure that I really...
I’m using NRF Connect SDK 3.2.4 with the nRF54L15-DK. I’ve successfully used the nrfx_gppi_conn_alloc() and nrfx_gppi_conn_enable() APIs to connect a timer to a GPIOTE output...
Hi, I am starting to get into the Nordic world and want to design my first pcb with nordic chips. I would like to get a review on my schematics and the pcb. I am mostly interested...
Hi!
I am evaluating some nrf9151 boards using the DECT NR+ stack. I have made my own PING test using UDP to test latency and loss.
Setup: nRF Connect SDK v3.3.1, DECT...
Hello,
I would like to know wich step I forget to do to send more than 20 bytes in NRF Connect app to a BL652. I followed some talks and subjects about it but it's doesn...
I am using ble_app_uart_c example to scan nrf beacons. Facing strange issue with debugger.
Enabled RTT and disable UART Logs, when i connect debugger and put break point...
Dear, I have bought the nRF5340 DK. I have installed nRFConnector and Segger Studio. Now, I want to test Blinky project. I connected a USB cabel to USB connector which is...
I have a receiver , transmitter application. I use a custom board as transmitter. I would like to use pca10040 as receiver but currently i use it as debugger to my custom...
Hi,
Our company has produced a batch of BLE products, and the 10uH inductor model used above is SDFL2012S100KTF. The rated current is not as large as the current value...
Hi,
I close the uart log and open the rtt log
why uart log can be used still?
why rtt log display error state?
I set the log config like this:
I set the test...
hi
i have this error
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol app_timer_cnt_get (referred from max30105.o).
in this code part.
the example is...
I have a program that runs great on the dev kit, however after uploading the code to a custom board based on the nRF52810, it does not seem to run.
I upload the code by...
Hello,
I need to connect a custom I2C device to the nRF52-DK, and I am using the sdk v1.6.0-rc2.
I am new to this development environment and I don't know how to initialize...
What is the max nb of periodic advertisers that can synchronize to a single receiver?
The bt_le_per_adv_sync struct defines a uint16_t sync handle so I infer that at least...
I am using the following example to load the code with Segger debugger and it works.
nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_blinky_c\pca10040\s132\ses
Now...
I noticed that when a BLE client disconnects and then reconnects to the, instead of receiving all data arriving over the UART from nRF9160 to nRF52840, there is a delay of...
Is it possible to perform two TWI Consecutive reads without sending the stop bit in between?
Example: Read 1 Byte - represent length (xxx) of data to come with second read...
I am trying to build a project with Visual Studio Code that uses MCUBoot. I have created a new project based off of the "Hello World" sample, which runs on my nrf52840 without...
Hello,
I have created different characteristics with the CCC macro (BT_GATT_CCC) that share the same "Configuration changed callback" function.
Inside the function below...
