Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I'am working on nrf52840 and base on a sample hci_spi. I use spi1 and tried several different pins, they all works fine.
but when i disable qspi and try to use the pins...
Hi,
I am doing a simple thing with string formatting:
sprintf(tmp_str,"%d.%d.%3d", version.major, version.minor, version.patch);
The version structure has values { 0...
Hi, This time I'm on NCS 1.3.0. Board definition is derived from nrf5340pdk_nrf5340, with some minor variations, and it is out-of-tree. I think it is OK. Since I moved also...
Hi there,
How can I manually awake my advertiser which is in low power mode, to start advertising and get it back to sleep after it advertises certain number of packets...
Hi,
I'm having some troubles with the Thingy:91 because it became unresponsive after I flashed the device with the mqtt_sample firmware.
I built the mqtt_sample with...
Hello everyone,
I am having an odd problem. I am using an SoC based on the nRF52832 (the ISP1507-AX). So far I had been using ncs v1.6.0-rc2 during development. Recently...
hi support team，
customer have one question, when 9160 attach the network, which one does it choose (the best signal or the first base tower discovered)?
especially when...
Hi Dev Team,
I am developing the weight scale product using nrf52840 development board. We connected the nrf52840 using the nrf connect app ( Provided by nordic).
Now...
Hi, I'm using the BC805M EK (nRF52805) . I would like to pull up pin 20. Here is my configuration in pca10040.h. However, pin20 cannot be pulled up. It's always pulled down...
Hello Devzone Community,
I am trying to develop an nRF9160 firmware, based on Nordic's sdk-nrf v1.6.1 code base. This work is a Zephyr RTOS based application. In early research...
Hi, I would like to know all of my possible options for improving the communication range between 2 nodes in ble mesh. I am working with the nrf5 17.0.2 SDK and the nrf5 SDK...
Hi everyone,
Explaning my project: an external device transmit via UART to nordik nrf52840DK device with UART peripheal firmware, this is connected to another nrf52840DK...
I'm testing the http functionality. In my code I test against 2 different servers, one plain http port 80 "postman-echo.com/post" The second server is private https server...
