Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi,
I have a mesh provisioner with the provisioner example in the mesh sdk. When I try to provision a device that is next to the provisioner, all works.
But when I try...
I want to send sensor data using sensor_server_status_publish function, however struggling with data marshalling. I get unknown property ID or no data at all displayed in...
Hello
I am using sdk v17 and nrf52dk and implementing sensor encryption(AES CTR mode) and simple nus service. After reading the sensor to saadc, I want to encrypt and transmit...
Thanks in advanced. I'm using nrf52832 with nRF5_SDK_17.0.2. I try to measure adc time consuming as below:
I find when timer sample rate is 500ms, then adc time consuming...
Hi:
I am doing a project which will use both PDM interface and bluetooth transreceiver, PDM interface is used to receive audio data from a MEMS microphone and Bluetooth...
We have a design that uses a simple custom board with an NRF52832 chip, button, accelerometer and onboard battery. For many phones, the operation is quite stable - we connect...
Hello all:
I've developed an nRF52810 application based on the UART example, but when I include buttonless DFU support to my application, it doesn't work. I'm using SDK...
Hi,
now I had achived the function to communication using the esb in nrf52832 that one to one,but I need to achive multi tx device to one.
if there not doc for me to achive...
Hi
Strange that there is no example for such popular code which will allow changing the iBeacon setting parameters (like: name, power, interval etc). with a smartphone application...
Hi everyone,
I'm trying since a few days to connect the Thingy 91 to the network with any result at all.
This is my configuration:
Modem firmware: V 1.3.0
Application...
Hi,
Am trying to store the data fetched through ble scanning to the flash memory of the nrf52840 DK. So I have been making use fo the flash_storage example in the SDK/examples...
Hello,
Our Peripheral server application regularly uses a stream of notifications to transmit data to a Central client. We have a rare error in which sd_ble_gatts_hvx returns...
app time loop update 200 byte data use fds by 10s ,then after many time error happened, update_user_flash is update API, write_drop_record IS loop write API in app time, ...
When running in High Voltage mode, it specifies a maximum of 7mA of external power draw on the Vdd output. It also specifies the voltage accuracy of -10%/+5%. This is a very...
HI devzone
Everytime after i executed "nrfjprog -f nrf53 --recover" on nrf5340 DK
i see it write around 4KB data into the flash. do you know what is the meaning for this...
