Hello,
I have 2 Memfault projects that I'd like to rename, but I can't find any way to do this through the web app, and the API authorization keeps getting rejected (tried...
Hello, I'm working on a prototype device based on the nRF9151 DK.
HW: nRF9151 DK, nRF9151 LACA A1A Tested with modem_shell sample app, NCS v3.4.0.
Symptom: on boot, "The...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
Hi,
I am using nrf_drv_clock_hfclk_release (); in order to release the hfclk, before the call, the internal counter is 1 and the module is initialized.
because the counter...
I'm working on the NRF Connect SDK v1.6.1 and building the zephyr\samples\net\gsm_modem project, since I'm trying to set up and operate a Nimbelink modem. The code references...
Hi everyone,
I would like to change the output voltage and current driver strength of some GPIO ports on the nRF52840. I am using the zephyr driver "gpio.h" API, but the...
When I try to connect to a previously bonded device, I'm getting
Disconnected (reason 0x3d)
and bt_att: Unhandled ATT code 0x1d
and if I delete the bonds again and try...
I am writing a coordinator application based on the zigbee CLI example. I am using SDK for Thread and Zigbee v4.1.
I am using a function in zboss_api called zb_secur_ic_get_list...
Hello,
I'm using SDK nrf5_17.0.2 on nrf52840
I'm implementing a custom nrf block device for a spi nand flash, and I'm getting trouble with the calling site of the nrf_blk_dev_read_req...
Hello Everyone,
I am using NRF52840 development kit, I have compiled the code using SDK15.0.0. I am using soft device as well. I have to implement flash protection in my...
Hi,
I’m finishing the design of a nRF5340-based custom board featuring a NFC coil-inductor antenna. Will orientation of track turns - clockwise or counterclockwise - affect...
Hi,
I am looking for example/ sample implementation of secure boot/ erase using NCS SDK v1.6.x, suitable for nRF52833.
Please point me where I can see such code, or document...
Hi,
I'm trying to integrate buttonless dfu to our project. We don't have any security concerns and given the existing project constraints, it's not desirable to use peer_manager...
Hello,
I tried the smp_svr example with the nRF52-DK of sdk 1.6.1., i compile the solution whit segger v5.50c
I connect with the NRFConnect Device Manager app,
I try...
Hi all,
I am trying to get started with the Nordic thingy 91 but I am not able to update the latest firmware.
The programmer is only showing one Serial port. The instructions...
