I found some examples on dev zone how to read RSSI during connected state:
Function report RSSI but as a positive value around 230. How to recalculate it to dB. I see...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I am using the S312 protocol stack on nrf52810, with both BLE and ANT+enabled, to transmit heart rate. It can be used on most devices, but it is difficult to connect to 'wahoo...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Dear Nordic teams,
we need to develop a wireless audio product with .
Is it possible to develop our 2.4G wireless private protocol by operating registers on the nRF5430...
this works well with an Apple 11-13, but on 14+ Apple has removed the second antenna from the phone, so it cannot do ranging natively.
the AR approach does not work for...
I don't know why sample code is not easily compiled.
I have to add many feature such as CONFIG_SERIAL=y on prj.conf
This is not a sample.....
Anyway,
I cannot run...
Hi
I'm using the pawr_sync and pawr_adv samples as references in my project. I have implemented them so that the sync node scans for new syncs for n secs at a specified...
Hello,
I'm using an nRF52832 and an accelerometer/gyro to record data and send it over Bluetooth. My end goal is to store this data in large chunks, and then send it all...
With the recent release of SDK 2.8.0 enabling tracing with Segger Systemview locks up the system.
The offending issue is buf = net_buf_alloc(&hci_cmd_pool, K_FOREVER); which...
Hi,
My customer asked about using nRF Cloud for device firmware updates and maybe more, and I'm trying to figure out if this is possible and how difficult it would be to...
Hi there.
I'm currently working on driving a radio_test example using the 7002DK. I downloaded the radio_test example using nRF Connect and ran the bulid to drive it. The...
Existing FW developed on PCA10040 EVB, moved to EVM-BC805 which is the chip for my final board design. I applied the patch that I found to SDK 17. However this anomaly function...
I just bought a new laptop: IdeaPad 3 15IAU 7 running Windows 11 and I try to use it and the "nRF Connect for Desktop v5.1.0" and its "Quick Start" option to communicate via...
Can you please help us to convert following snippet from dts to mp_static.yml to use it for DFU applcation. We have external nand flash which used with littlefs and internal...
Hi all,
I have to measure the frequency of a PWM signal routed to one of the nRF52840 GPIO pins.
The signal frequency is ~3MHz.
The measurement is done with the help...
I am encountering the error message " <err> net_pkt: Uncontiguous data cannot be linearized " when already connected with nRF7002-DK to a Wi-Fi network using the EAP-TLS authentication...
I'm following the nordic academic courses, which are very nice by the way!
I've now followed three topics and I find three different variants which confuse me a lot: ...
Hi there,
So in my previous posts, I have been asking questions about setting i2s on two nRF devices in different modes. I have been successful in making it work.
...
