Hi all,
I'm working with the nRF52805 (QFN16) and was curious if the nRESET pin (P0.21) can be disabled via the UICR->PSELRESET[n] mechanism, as is possible on other nRF52...
Hello,
Is the NRF7002 pre-certified for the RADIO EQUIPMENT DIRECTIVE 2014/53/EU (RED directive) ?
Is there a recommended antenna design that would ease certify a product...
Good day, I was attempting to test the radio performance of the NRF54L15. I ported over the Radio_Test sample project to try and transmit an unmodulated carrier wave at a...
My task is to mount a littleFS system on the external flash memory, so I can save files.
I am using the littlefs filesystem sample from
zephyr/samples/subsys/fs/littlefs...
Hello.
How often are the LQI and RSSI values in the coordinator updated for a child?
Preferably I would have liked to get some kind of notification every time LQI and...
I am currently developing a project using the nRF51822 with SoftDevice S110 v8.0.3 in Keil uVision.
To properly manage RTE components and dependencies, I need to use the...
Hi,
I want to configure P1.02 and P2.06 as normal GPIO for my nrf54l15 custom board. For this I have added the following in my .overlay file
From https://devzone.nordicsemi...
Hi, i am working on servo motor using nrf52840 development kit , i want to run parallely four servo motors , i have merged the ble_app_uart+pwm library example ,
1. As of...
Hi,
I am using an external RCT module to provide 32.768kHz square wave for the nRF52832 instead of an external crystal oscillator. When the system goes to deep sleep mode...
Hello,
I'm aiming for flashing the nrf52832 via SWD via my own SWD implementation.
I'm good so far with the init phase, reading IDCODE writing registers. Long stort short...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
I modified ble_app_blinky with below...
I am getting ecg data from max30003 IC which i want to send via BLE to and application. I have the Ble code working on its own and the SPI code to get ecg data working on...
Hi,
I am working on nRF52840 (dongle) using nRF Connect for desktop on windows 7.
I was able to write the "peripheral/blinky" example and was able to see the output...
I am willing to use the uart or uarte driver to be able to have to buffers for the Rx, I have a huge flow of data at high sped arriving to the UART, I have read for few days...
My goal is that disabling the interrupts other than soft device interrupt.
I think that this is achieved by d isabling interrupts below a certain level (in this case, 2...
Hello,
I am using NRF52840 with SDK 16. In my project I need to restart the chip after a successful pairing but I can't find any event that can make me sure about pairing...
Hi,
On zephyr, I am using the cryptocell as my backend to do the following operation:
mbedtls_entropy_context entropy; mbedtls_entropy_init( &entropy );
My memory...
Hello All,
I used the sample Serial LTE modem code and downloaded it to nrf9160. Can some please help me with a sample AT commands to send to tcp/udp server and how should...
Tsu_dat (300ns min) and Thd_dat(500ns min) are more stringent than NXP I2C spec .(Fast mode)
Since most IC vendors design their I2C bus with NXP I2C spec, they are not meeting...
Greetings,
The only examples I can seem to locate of using the Coexistence Interface on nRF9160 is with the internal GPS but the documentation states that "COEX0: Input...