Hi there,
My nRF5340 application requires the use of SD card with DMA and BLE transmission. Howerver, as soon as I turn on the device, I get the following errors:
A...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
Hi. I want to use nRF52840 as a gateway(connected to cloud via Ethernet). I have to transmit a vast number of nodes' data to the cloud via the gateway. To begin with I can...
Hi Sir/Miss,
We want to test advertising interval time of peripheral device to follow APPLE accessory guideline.
We found some topic on forum, it mentions that uses...
I have a custom board. It has its Tx and Rx combined into one wire bus. I am able to transmit data on the bus. But I am unable to receive any data on the board. This is because...
I have nrf9160dk. I want to give AT commands to the sdk through the processor instead of giving it from the PC i.e want to program the processor in a way so that we don't...
For testing direct advertising i used sdkv10 keyboard example, but when im disconnected device form nrf connect manually its resetting. I debug code found that in BLE_ADV_EVT_PEER_ADDR_REQUEST...
hello
I am a newbee in BLE dev.
I try to connect the sensor to the Adafruit board thrut BLE. The sensor is Sensor it is saw on nrf connect iOS as
I mod the HRM central...
Hi,
I am try to configure internal RC (LFCLK) but device hang in "sd_softdevice_enable(&clock_lf_cfg, app_error_fault_handler);" API.
Changed in "sdk_config.h" to enable...
Hi
When we enable the ADC on the nRF9160, we se a considerable rise in current consumption in standby mode, from sub-100 µA to several hundreds of µA (~400 µA). How do we...
Now that most or all of the Nordic nRF5 SDK is covered by the permissive 5-clause Nordic license (as of June 2017: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog...
Hi
we are working on ble_nus_c multilink implementation and had problems when more than 1 server is connected: we've noticed that data get mixed between servers.
when...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
Is there any sample code integrated with HDC2010 Temperature & Humidity...
Hello,
I use a debugger probe (Segger Jlink) with the sdk_config.h setting SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL.
When my probe is not connected, there my product is blocked...
Hi, I am new to Nordic BLE development and trying to create an application that has beacon functionality with firmware upgrade over the BLE with the mobile phone and Nordic...
