Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi,
I'm testing an interactive pyaci example in Mesh SDK v2.2.0 with two nRF52DK boards.
Interactive mesh provisioning and configuration example worked fine so I modified...
I'm using nRF52+SDK11.0.0+S132 . It currently has SPI, SPIS, TWIM, RTC. I want to remove SPI and I'm getting: ..\components\drivers_nrf\spi_master\nrf_drv_spi.c(56): error...
Hello,
I'm using the nRF52 DK with SDK 15 and SD132 6.1.0. I have a custom service running that requires periodic characteristic writes. Occasionally when writing to this...
hi guys!
i'm trining to develop the nrf 52840 devkit in particular for the ble use.
from the documentation i didn't find anythingh about send a message to the dongle from...
Hello guys,
I am using nrf52832(PCA 10040) and transmitting radio packets. I want to collect the packets using raspberry pi. Is it possible?. If yes, how are the ways we...
Hi, everyone. I've been trying to migrate from the SDK 14.2 to 15.2, but I've been having trouble getting one new function to work. I previously used ble_advdata_set() to...
Hello,
I've checked a few related threads, but without any success.
I need to react on "Data Ready Interrupt" and read data from SPI. SPI and Device is initialized before...
I'm am trying to select an LDO to provide the VDD_GPIO power rail for the nRF9160 and am interested in selecting either a 100mA or 200mA LDO. Can Nordic provide a rough order...
Hi,
I was trying to communicate with an I2C device, which's address is 0x7C
But I always got NRF_DRV_TWI_EVT_ADDRESS_NACK event, so I took a check on the TWI wave:
...
Hi Nordic Team,
Meanwhile we are working with Laird BL654 which uses the nRf52840.
My questions:
1. Can we flash gazell examples on Laird BL654 with Segger?
2. If...
i'm trying to get distances between nrf52840 ble transmitter and receiver, using measured rssi upon receiving ble_gap_evt_adv_report_t from ble stack. in order to calculate...
In file sdk_config.h, in order to configure a calibration interval of 8 seconds, what number should be used in the define NRF_SDH_CLOCK_LF_RC_CTIV?
The time units are not...
