Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
I have an embedded platform running JerryScript. Now, I need to add BLE functionality to it. The BLE module (connectivity chip) will be used is nRF52840. For this, I guess...
I’m trying to program a custom board with nrfjprog, but cannot get it connected correctly. (Connection is standard SEGGER cable, segger mini edu)
nrfjprog -f NRF52 --halt...
hi ，i have a problem! how to slow down the update speed when bootloader receiving the pack. my project is base on the SDK 15.2.0,s112 ,secure_bootloader example ,nRF52810
Dear nordic,
i want to create a low power current consumption ADC. i don't need adc value in every time. my need is just take adc value and disable it.
whenever i want...
HI,
I'm currently working with two chips RF24L01+.
Each chip switch in sending role to receiving role several times. By default, I set them in sending role and I whait...
I use sdk15.2 and nrf52832.
I copy i2s examples to nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ ble_app_hrs ,and nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ ble_app_hrs_freertos...
Hey all,
So I'm new to the Nordic world and I am having some trouble programming the SoftDevices API. After I compile my code, I get the S112 hex file and try to use this...
Hi Nordic,
I am working on a NRF52 DK with the example code ble_app_interactive. I am using the NRF52 DK as a central and trying to connect to a peripheral hearing aid....
Hi guys. Why the Android Mesh app can not receive the the publish data from the 0xffff address?
As we do below:
step 1 : we use 2xP10040 development kit and an android...
Hey guys,
I'm working on a project and want to build up on the Nordic BLE UART example (mobile device app and node firmware). As far as I know the pairing between the node...
hi all,
I have added the dfu service in one of example of sdk_11 ble_scanner_hrs I followed all help available on this forum and made sucessfuly compiled code but it stopped...
Here is a thing that I want to develop.
As my understanding, if I want to connect with PC I must use the HID example to achieve the event.
However, is it possible that...
I programmed an nRF52 (PCA10040) with the ble_app_beacon sample app and can see it advertising. However the nRF Beacon Android app does not detect it. nRF Beacon seems designed...
