Hi,
When starting nRF Connect for VS Code, SDK v3.3.0, the message Unable to resolve configuration with compilerPath: "C:\ncs\toolchains\fd21892d0f\opt\zephyr-sdk\arm-zephyr...
I have recently purchased nRF52840 dongle which I wanted to use as a ZigBee sniffer. I bought it on AliExpress and it supposed to be original Nordic board, but it turned out...
Hi,
I have a project requirement to interface with HART, which is a protocol that specifies odd parity for UART. I recently found out UART odd parity isn't supported on...
Hi Nordic team,
I am working on nRF5340 and trying to enable MCUboot serial recovery DFU in single-slot mode with both signing and encrypted images.
Environment: 1. SoC...
Hello Nordic Support Team,
I am experiencing a startup issue with the nPM1300 PMIC. Below is the summary of my hardware configuration and the behavior I am observing:
...
Hi Team,
I am working on an nRF52811-based BLE application using nRF Connect SDK (Zephyr) and facing an issue while trying to store the device name in flash using the Settings...
Hello Nordic Support,
We are developing a project using two setsof nRF5340 DK with the nRF7002 EK attached. We are trying to achieve coexistence between Wi-Fi in SoftAP...
Hi,
I want to store some data into flash and need to read before calling gap_params_init() in proxy_server demo.
1) when I am initializing flash manager using flash_manager_init...
Hi I wanted to flash a firmware in a Thingy52, I used Segger embedded studio and NRF52 DK to do that. I used the right cable but after flashing my Thingy52, it doesn't blink...
Hello dev zone !
I shall design a compact hardware solution wich is cost sensitive.
I need to use a NRF52832QFAA, I need to provide a 16mhz clock to a hardware peripheral...
I want to implement the function of long Attribute Value reading and writing in BLEV4.0. How should nrf52832 sdk14.2 implement this function? Is there a routine for reference...
I am trying to create a beacon application based on nrf52810.
I am using the following…
* SDK: 15.2.0
* IDE: Segger Embedded Studio
* Hardware: PCA10040 V1.1.1
...
hi.... i am working on ble_uart in segger ... while i am debugging my program stop at nrf_breakpoint_cond ...
how to enable the logging ... please have a look at pic......
hi...
i merged the ble_uart and twi sensor program in segger 15.2 using nrf52832
i have flashed the program successfully, i am getting fatal error while i am debugging...
Hi Sir
We'd want to make lot of nrf52840 devices, and all devices included open bootloader program,
however, the each device USB SDFU port number are different (COM30...
Hi,
I am usig nRF5_SDK_15.0.0_a53641 and writing a program with keil .
I am tryng to read data from the acceleration sensor( LSM303DLHC ) bu communication with BLENanov2...
Hello All,
Confirm the chip set replacement for the NRF51822 with NRF51802?
Can anyone suggest me which one is better with reference technical features.
Thanks
I used nrf52832 sdk14.2 development, modified on the basis of the ble_app_template project, and ported some of the user code previously in sdk12.3 to sdk14.2. After I open...
Hi
Over the last years working with Nordic I struggled from time to time over the disconnect reason 0x3E (BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED) on our devices with Central...
hii...
i have programmed the ble_uart with twi sensor ...
complied very successfully
but while i am debugging i am getting error in void twi_init()
why and also fatal...
Hi,
Here I met a problem, please help.
I am using proxy.c to establish an data link with smartphone via mesh_GATT.
What I am doing is like this:
For TX ,
it is...
