Hi,
I have a project requirement to interface with HART, which is a protocol that specifies odd parity for UART. I recently found out UART odd parity isn't supported on...
Hi Nordic team,
I am working on nRF5340 and trying to enable MCUboot serial recovery DFU in single-slot mode with both signing and encrypted images.
Environment: 1. SoC...
Hello Nordic Support Team,
I am experiencing a startup issue with the nPM1300 PMIC. Below is the summary of my hardware configuration and the behavior I am observing:
...
Hi Team,
I am working on an nRF52811-based BLE application using nRF Connect SDK (Zephyr) and facing an issue while trying to store the device name in flash using the Settings...
Hello Nordic Support,
We are developing a project using two setsof nRF5340 DK with the nRF7002 EK attached. We are trying to achieve coexistence between Wi-Fi in SoftAP...
I try to get the one button sample to work. There were several details missing to be able to compile and run this sample, which was very frustrating. After editing/updating...
Hello all,
Accordingly with nrf52832 product especitifation when radio Rx is active there's a additional 5.4mA consumption. My doubt is how softdevice s132 handles the Rx...
hi!
i am working with the nrf52 and i am looking for a timed sleep mode, meaning, a function that goes into sleep mode for a given duration.
is there anything like that...
Hi all,
I am working on my Central device to request pairing to my peripheral ( I asked about the peripheral in my previous post , both are running a nRF52DK and SDK13...
We have shifted our development from nrf51422 QFAC (32kB RAM and 256 kB Flash) to nrf51822 QFAA (16kB RAM and 256 kB Flash).
I'm unable to run dual bank ble bootloader...
Hello,
I would like to signalize that the DFU process is running. I mean when I start to upload the application into the CPU, then a LED (for example) is ON, after uploading...
We have been successfully using the Softdevice s132 to communicate with a smartphone using BLE. However, we have run into an issue with the compliance testing in the new requirement...
Hi All,
I am a beginner in app development. I am working on a project where i am supposed to transfer texts to my pca10040. Although i wanted know if i can modify nRF Toolbox...
I'm taking a look at the timeslot API example here , which was linked to in the answer to this question .
Very interesting! As I gather from the documentation for S110...
Hi,
I would like to have accurate (1-5ms), synchronized timestamps for logging events from a set of nRF5x boards, spaced tens of meters apart. Each nRF5x board is connected...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
I am struggling to find a starting point to be able to program the beacons. I'm completely new to this but want to be able to change the tx power so that they are only visible...
In my application, a static passkey is given to the user(I have implemented static pass key in my application and it is working).
Suppose the Nordic device is advertising...
In "ble_app_hrs_freertos" project, I try to change NRF_SDH_BLE_GAP_EVENT_LENGTH to 320 and NRF_SDH_BLE_GATT_MAX_MTU_SIZE to 247.
And when I try to connect to the nrf52832...
Hi ,
I evaluate the I2c communication of your chip nrf52832.
I have few problem.
Write fonction
Is use your Tx fonction,
uint8_t reg[2] = {CCS811_REG_MODE...
Hello,
I used translation software.
I enter system on mode from the power_manage of the function.
But I do not understand system on mode.
In the system on mode is...
