Hi, I’m working with an nRF52840 DK and trying to use two UARTs simultaneously. I’ve configured UART1 for debugging (console and shell output) and want to use the default...
Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
I am getting the following build errors when working with both DFU (MCUboot) and the file system (FAT FS) together. Errors: D:/ncs/v2.9.0/zephyr/drivers/disk/flashdisk.c:533...
Hello,
We are working on an audio project where we are using nRF5340 Audio DK. We want to externally interface the digital microphones without using the on-board codec ...
Hi, We want to integrate LORA LR1110 for the final year capstone project. From the documentation we have understood that Kit is fully compactable with Arduino UNO. But SPI...
안녕하세요
nrf9160DK 보드로 개발하고 있습니다.
blink 예제로 컴파일 및 다운로드되었음을 확인했습니다.
SDK에서 예제AWS_IOT_MQTT로드하여 테스트하고 있지만 아래와 같은 오류가 발생합니다.
해결 방법을 가르쳐 주시면 감사하겠습니다.
zephyr/subsys/net/libsubsys__net...
Hello all,
I'm currently modifying my Analog Input circuit schematics to improve precision.
I'm adding after my voltage divider, an opamp as a voltage follower to ensure...
i have 3000 bytes of data placed in flash from 0x20000. i want to calculate hmac for the same data.First, can we calculate hmac for such huge data?If yes, then how can i calculate...
I'm using SD 110 and the PCA10001 board.
I make the call to:nrf_gpio_port_read(LED_1), where LED_1 is on, or high. This call always returns a 0. How can I read the state...
Hello!
I'm trying to advertise my custom service. After setting everything up, when calling ble_advertising_init I receive error 0x7.
static m_adv_uuids[] = {0x1523...
Hi,
I ported some SDK code into my device (SDK 10 adapted for S110v7x) where I can successfully Bond my device and use the Services I need (ANCS on my case). I have simplified...
Hello,
I have a project that I want to transfer it from nrf51 to nrf52 (the changes are from nrf51822 to nrf52832). I followed the migration guide. And now it debugs so...
Hi all.
I have phone with nrf Tollbox and central device with DFU, SD130 2.0.0, SDK11.
I would like flash application to central by OTA when I enter password in nrfToolbox...
Hi Nordic,
EDIT: I am using nrf51422, with S210 v5.0.0. Everything that is below is referring to ANT protocol
I want to know if the thing that I am planning to do is...
I download the example of multilink central (S130) into nrf51822 .The central transmit 20 bytes to peripheral interval 50ms sometimes will reset.Anybody know the bluetooth...
Hi guys,
I have the NRF52-DK and want to power only the NRF52. So basically, I want to power it over VDD_nRF.
When I power my DK with a battery and then measure my current...
Hello!
Is it possible to read data sent from ble_app_hrs (peripheral ) to ble_app_uart_c (Central) on PC's serial monitor? If possible, how can i achieve this and which...
Hi,
I programmed nRF52 DK with BLE_APP_UART_SAADC_TIMER_DRIVEN with AIN6 pin as input and is working correctly. But when I programmed the same code in BMD300 the adc count...
I'm running an nrf52832, using SDK 11.0 and the S332 soft device. I've had instances where it seemed my flash data, stored with FDS, was corrupt after a firmware upgrade....
Hi Nordic,
I am having problems knowing what exactly happens in the following situation:
I have a connection established between a master and a slave, and the master...
Hi,
I have started your tutorials and just complement this one. devzone.nordicsemi.com/.../
Now when I tried to download other programs on the development kit, I get...
