Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hi :
I have problems ,for gpiote interrupt hanlder can be hanged up by softdevice. In normal use ,I should pull up sck pin of my private ADC chip for less than 10us and then...
Hi,
I'm using the SDK 12.2 with the sd 132 3.1.0, and actually I'm trying to send two separate advertisements wich I'm swapping every "radio notification event", but I...
I am working on modifying the ant+ sdm example to hack my treadmill. Got the example running and talking to my Garmin watch and the display simulator. All of that seems straight...
This problem didn't appear every time when I upgrade firmware. If I restart my app again, sometime the SDK can works well.
Anyone can help? I'm use SDK in Android, Legacy...
Hi,
I am using nRF51-DK and nRF5_SDK_12.2.0_f012efa. I have programmed Proximity example from the SDK to the Development Kit and was able to successfully program the DK...
I have a function with a return value in the time slot, after the function is done inside the time slot signal callback function, I want to use the event callback function...
Hi
We'd like to set the pairing timeout when using the function sd_ble_gap_authenticate(conn_handle, p_sec_params) . The reason for this is that we are setting the connection...
(/attachment/182b723590b3c447267d5aed62b5405f)hi, i want to work on PWM to controll the vibration coin frequency for certain time period and also to change RGB values of LEDs...
Hi!
I'm reading the PS for nRF52832 and I can't find a clear answer on the following question.
If I set up a GPIO channel with pull-up/pull-down in the PIN_CNF[n] register...
Hi, I'm learning to use the nrf52832 (PCA10040).
I'm on SDK12.2.0 S132.
I've done those basic tutorials while merging codes from the examples.
My code can currently read...
Hi, i am working on TWI sensor example in SDK11 i have connected MMa7660 to PCA10040 board as per the GIPIOs. and am integrated BLE app uart to the same TWI sensor example...
Hi,
I am using a custom board with a nrf51422, SDK11, S130 v2.0.1 with central role.
I have made changes on the code to change from MID bandwidth to High. I added the...
Hello,
I'm using the Nordic BLE-UART service found in the SDK. This is the "ble_app_uart" file in the SDK examples for the Nordic nRF51822. I'm basically sending JSON back...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make only app image for DFU.
I made a command as below refering to github.com/.../pc-nrfutil.
...
Dear all
Currently we are using version 9.0.0 (nrf51422 family---> using for 51822 chip) & now we are trying to use 12.2 ("nRF5_SDK_12.2.0_f012efa.zip").
Is there...
