Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hi everyone, I have one question shown in the title. I try to add a second service in "ble_app_uart" project (the project is in the SDK for nRF51, SD130 v2), I did not change...
Hello,
I was using the nrf24LE1 where i used hal_nrf_set_power_mode() to set the radios' power down mode. Options are power-up and power-down. This is when i was using...
I have a system, with cc2540 as central and n51822 as peripheral with s130. Sometimes while they are close to each other, the connection link gets lost.
I disabled updating...
I'm using SDK14, S132 5.0 and nRF52832, and trying to enable and disable softdevice in my application. In main function, the power management loop is like
while(1)
{...
I am using SEGGER Embedded Studio for developing mesh network on nRF52832. For curiosity I pressed the BOOT/RESET button (SW5) while applying power to the board and it entered...
I want change project "record_launch_app" purposely launch my own app use the NFC tag on an Android device? Where should I take "m_android_package_name" of my app?
I used...
Hi,
I have a basic characteristic on which I would like to write. I did this on so many projects without any problem but here, the value handle of my characteristic doesn...
Hi,
I'm currently testing the pc-ble-driver.
It seems its only supporting exactly one FW version and I wonder why.
As far as I understand it currently supports v2 (S130...
Hi,
I'm using nrfjprog with nRF52, SDK13 & S132 soft device.
I do not use mergehex during my development cycle: I flashed S132 hex once, and only reflash my application...
I programmed to nRF51 DK, the first time the device is connected to mobile phone.It works, but if i turn off the nRF51 DK and then turn it on.it is connected but it cound...
Hi
I am going to implement a BLE device according to a customers specifications.
The service UUID is defined as
00000001-0000-1000-8000-XXXXXXXXXXXX
The characteristics...
I can not transfer more than 61 bytes to the Android device with commands "ble_nus_string_send". When I send more than 61 bytes my device received only 61 bytes. But BLE_NUS_MAX_DATA_LEN...
When I use the "nrfjprog --eraseall -f nrf52" command, I get "ERROR: The --family option given with the command (or the default from nrfjprog.ini) ERROR: does not match the...
When I try to run the 3 server, 1 client light control example, This is the log that follows:
Client log
<t: 0>, main.c, 318, ----- BLE Mesh Light Control Client Demo...
