Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
I am running the Buttonless DFU example in SDK 12.2.0 on a nRF52832. When I connect with NRF Connect, I can see the DFU control point but I can only enable notifications and...
I learned that paring is consist of 3 phase (Exchange of Pairing Information, Authentication, Key distrbution) and TK, STK are generated at the phase of Authentication and...
I have a central application that I need to add a peripheral role to. I don't need to pair or bond in any of my connections, so I based my app on the ble_app_uart_c example...
Hi,
I'm currently running two separate TWI-instances on my nRF52 DK with SDK 11.
Each instance runs quite well with no issue, except for when instance 1 becomes active...
Hi,
When nrf51822 is connected via bluetooth LE to an iPhone application, is it possible to check the actual connection interval (between MIN_CONN_INTERVAL = 20ms and MAX_CONN_INTERVAL...
I have a project on a Ble Nano using Nordic SDK 8.1 that I currently compile entirely from terminal using a Makefile. I want to convert this project over to use Keil so I...
Dear sir,
I want to use NRF24LE1-F16Q48-R7 as a standalone controller in one of my application but it is not available with any vendor .
We want to use this For Low...
i want to know why there are 2 pages reserved although i mentioned i configured the number of pages to 1. It is used for what ? In fact, I need only one page for my data,...
Hi,
When compiling my program on SEGGER embedded studio I get the error:
Compiling ‘main.c’
main.c
expected expression before '{' token
in expansion of macro 'NRF_DRV_ADC_DEFAULT_CHANNEL...
I'm writing a central app using the pc-ble-driver project with an nRF51 dongle. This is to test our product, which is a peripheral using the nRF51822. The test central needs...
Dear All,
I have developed a BLE system in which nRF52832 is being used as a peripheral and central concurrently. I am also using BLE_GAP_CONN_SEC_MODE_SET_ENC_WITH_MITM...
Hello,
I have board pca10040 V 0.9.0 2015.41. When I program nrf and then issue a nrfjprog --reset -f NRF52 everything works fine, however when I execute nrfjprog --pinreset...
I don't understand OOB used in BLE security part.
Is this a communication out of 2.4 ~ 2.48 GHz frequency band?
Or is this one of method of pairing procedure(to generate...
Im currently working on a project and long story short im stuck on getting the nRF24l01 to communicate. I believe I have the Tx side of things working, however as I do not...
Hello,
We have connected Nordic+ MPU 9250 and able to read sensor values through UART display, but we wanted to do some excercises and read values, but it's not possible...
