i have some bare-metal RF code that runs on my nRF52-DK, which i'm currently porting to my nRF54-DK.... functionally, everthing is working just fine -- the boards can in fact...
Hi,
1. It was measured that SWD0_SELECT needs to be connected to VDD to program the external nRF54L15 2. Will the document or the program be modified here to make it consistent...
In my application we have an nRF514L configured as an SPI target. Page 830 of the nRF54L datasheet (version 0.8, dated December 2024) documents that the SPIS peripheral requires...
I would like to use native CMake rather than West to take advantage of CMake Presets.
I have been able to make this work on the command line using the following command...
I developed a BLE application for the nRF52832 using NCS v3.0.0. The application runs correctly when flashed to the nRF52 DK.
However, when flashing the same application...
Does Zephyr support automatic reconnection of the Wi-Fi if a connection is lost? I can't find any documentation on this, or code examples. It seems like every example connects...
We're building a prototype board which uses the nRF52833 and want to tune the RF components. The radio_test sample in SDK 3.0.0 doesn't seem to support the nRF52833 SoC. Is...
Hi All,
I need to read the data written on RX characterstics of nrf_uart Service from my board using bluez.
I'm using interactive mode of gatttool with my Nordic sensor...
Hi,
I need to design a small nRF52 board, with a 3cm by 3cm size. I am very new to antenna design, so i have some questions, in order to avoid ruining it. The reference...
I'm trying to write 32bit word on flash memory every 25ms, but when I read the memory using nrfjprog I noticed that it write only 16 words (32 bits), in this code saveToFlash...
1,How do I send a data packet using BLE Peripheral? What API should I call? How should I prep that API? Do I have to care about the format of the data that will be sent, or...
For starters, I'd like to use an Arduino Uno to receive a Bluetooth signal from the nrf51 DK and
turn an LED on/off.
What materials do I need to do something simple like...
Dear Nordic developers,
SPI_MASTER peripheral behaves in a way, that I cannot understand from manual is it normal or no.
I have implemented something similar to loopback...
Hi.
Currently using the examples of
examples/ble_peripheral/ble_app_uart
examples/ble_central/ble_app_uart_c
from nRF51-SDK V10.0.0 ble_nus and ble_nus_c.
We can...
I'm experimenting with BLE multilink central S120 softdevice on pca10028 and several of my custom BLE devices based on S110 softdevice.
Is S120 multilink central capable...
hi：
I combined ANCS example and HID_mouse example @SDK 9.0,but there is an error when iphone connect the device ,err_code is 0X8010,(err_code = dm_service_context_set(&m_peer_handle...
Hi Experts,
I modified a DFU bootloader from SDK 9.0 for nrf51822_xxAA chip. However, I encounter code size overflow problem when building it.
I found the ROM1 configuration...
Here are my 2 scenarios:
I need a radio chip that will be used to form a mesh network in dense bush with each node up to 150m apart. Is this possible?
I need the...
Hi all,
Edit 25 Dec '15: Rewrote post for better readability:
I am trying to modify the dual bank DFU bootloader example to work on our custom board that uses a nRF51822QFAA...
Dears:
I try to use nRF52_SDK_0.9.0_0c82e3e SDK pheripheral pwm example and set the channel1(led2)
duty to 0.
But i still could get the signal about 400mv with LED2...
I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
Hello,
I want to add uart debug support to the BLE DFU bootloader (nRF51822, S120, custom board).
Therefor I increased the possible size of the bootloader (start 0x39800...
