I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hello all,
i am working with the nRF52832 DK and SDK11. Actually the Enhanced Shock Burst Communication is working. I can send and receive messages. From this point on...
Lets say, that I've got a chip with program in its flash. I know I can protect it from being read back, but can I protect it from flashing anything else through debugger interface...
we have two nrf51-dks and we wanna create a ble mesh.
how can we set a ble mesh and same time ble advertising on Nrf51422 DK (PCA10028 V1.2.0) Board with using examples on...
Hello,
is there a possibility on nrf51 8.0.0 softdevice to determine whether particular notification has been received by remote device?
I use sd_ble_gatts_hvx() to send...
I am facing some problems with the app_timer api. In my application I have created two app timers. The timer api is using the swi1 interrupt for its working. I am using it...
During DFU with the nrf Connect app I get the error REMOTE DFU OPERATION FAILED. Here is the log file:
http://pastebin.com/y7hFNSBq
Using NRF5 SDK12 / NRF51 DK
...
Hi
We are very interested to test the wireless range using Bluetooth 5, 125 kbps long range mode.
If we purhase two nRF52840 Preview DK boards, is there a easy way to...
Hi, Nordic
I have two nRF52 and one nRF24LU1.I want to use Gzp. two nRF52 pairs to the nRF24.
I use nRF5 SDK13 GZP device sample, nRF24 Gzp host sample.
But only...
Hello,
Currently i am doing some testing with the NRF52 DK.
I am measuring the time it takes to send and receive a BLE message.
I am using the high bandwidth setting...
Hi all,
Someone can give me a information about the difference between function uint32_t err_code = sd_ble_gap_adv_stop(); and stop the advertising with using the timeout...
hi everyone i'm using 9 axis imu sensor with the nrf51822 board and i'm confusing in how to calculate the roll,pitch and yaw values,can you please suggest me some methods...
I recently purchased the NRF52832-QFAA Nordic SoC, and am having trouble finding information in the documentation about FCC ID and CE mark testing. Thank you.
Hi, I'm trying to implement SOFTDEVICE_EVT_IRQHandler as in HRS example,
this is the handler source part:
for (;;)
{
uint32_t err_code;
if (!no_more_soc_evts...
I want to create voltage divider for ADC input so I need reference voltage for it. I was wondering if I take it out from DEC1 pin? Any how if I measure voltage from DEC1 pin...
