Hello, I am working on a project using zephyr as well as the nrf5340 MCU. For this test, I am on the nrf5340dk. My application requires I drive a PWM at 125khz. In my device...
Hi all,
I've build a custom bord with an nRF9151, I try to connect to aws iot but it's seems it's doesn't work probably cause by bad cert, I got AWS_IOT_EVT_DISCONNECTED...
Hello, We're developing a firmware for our board based on nRF9160, using ncs 2.7.0. We want to allow the user to set the certificates over i2c. How can we in a secure mode...
We are developing an IoT device that utilizes the nRF9151. We would like a review in the second round of our schematic and layout to understand if there is any issue that...
Hi
Is it possible to stream 128 kbps .acc, .lc3 or .mp3 Spotify audio from server to nrf9151 ?
It says it supports 300 kbps download, so maybe 150 kbps is realistic ?...
Hello,
I'm currently working with a custom board using the nRF5340 SoC, and I'm running into unexpected current consumption behavior.
When the device is in advertising...
I installed NRF connect I successfully built project when I flash I get success, but actually I can see project is not flashed what and how can I debug that ?
When connect to iphone4s, whitelist.irk will be generate,and whitelist.irk_count will be add 1
After that connect to Nexus 7 II bouth irk and addr will be generate,and...
Hello all,
I've had problems for several weeks with RF24 Library (enhanced fork). I use different Arduino and NRF24l01+. I know very well different documentation, and I...
use s130-0.5.0
A1 connect B1 with BLE_GAP_ADV_TYPE_ADV_DIRECT_IND, after this, A1 is slave, B1 is master,A1 can't send any type advertisement
use s130-1.0.0
A1...
Good afternoon,
I have developed a custom board based on nRF51822 device and SD-110-v8. For debugging I have been usign the Ulink2 tool with Keil. Now, I want to implement...
This is not working for me. My goal is to use printf() in my code. I follow the steps outlined in this link
..including calling initialise_monitor_handles(); before calling...
I was able to measure current with the test probes I have. However, I really liked the idea of test probes that were like the ones in the drawing below. I have not seen test...
I am using the PWM library in this repository for a nRF51822. I write the following code to generate a ~ 30% dutycycle 500 kHz PWM output:
#define V_CLK 5
static void...
Hello,
I am using Timer_2 with two CC registers configured, 2 PPI channels (one for each CC register in the timer), and one GPTIO_TE to make a PWM to control dimming on...
hi,
my nrf51822dk was downloaded s110 hrs demo,and it was advertising,i used a ble sniffer dongle to get the advertising data.the AdvData is "0B 09 4E 6F 72 64 69 63 5F 48...
Why is it a standard in nordic-supplied code to initialize structs with memset like so? An example would be:
ble_gatts_char_md_t char_md;
memset(&char_md, 0, sizeof(char_md...
//Edit:
So Hung Bui just told me in another question, that there is indeed a buffer of size 6 or so?
How can I decrease that to 1 (i.e. disable it) so that only the latest...
I have the nRF52 DK and cannot determine the silicon revision on it. Is it the 'Engineering A' revision and therefore is subject to all the Errata that is currently published...
