Hello,
I am currently using CADENCE for schematic design and have used Nordic's nRF9151 and nRF54L15 chips. However, the reference materials downloaded from Nordic's official...
I am having an issue with the nrfx_qdec driver in zephyr, I am trying to simply detect when the turn happens and the direction of the turn is. Most of the time this is triggered...
Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hello,
In ncs, I am working with \nrf\samples\ipc\ipc_service. I want MCUboot to build \nrf\samples\ipc\ipc_service\remote to run on nrf5340 CPUNET. When I CONFIG_BOARD_ENABLE_CPUNET...
Hi,
I am currently conducting measurements using channel sounding with my nRF54L15 boards. I am at the end of my master thesis, so there is not so much time left to really...
The nrfx pwm supports a number of events for a callback: /** @brief PWM driver event type. */ typedef enum { NRFX_PWM_EVT_FINISHED, ///< Sequence playback finished. NRFX_PWM_EVT_END_SEQ0...
Hi,
I have two nRF5340 DKs and want one to be server, one be client. I use NCS offcial code and simply buide them, however, " LED3 starts blinking green on every device...
Hi,
I'm using nRF51822 Beacon v1.1.0. Is it possible to detect that the beacon is being scanned? Is there any event generated during this process that I can catch?
I have been studying the ble_app_hrs example, but it has unnecessary functionalities, and it is hard to understand.
Do you have a simple application for transferring data...
I would like to use that chip with appropriate codec as wireles Tx/Rx set. I need of uncompressed audio signal and my sours will be analogue amplifier and the Rx module has...
Hello there,
I am using multilink_central example on nrf51822 Soc, and I charged S120 in the memory. I am trying to get the RSSI and the MAC address without getting connected...
I am trying to get the sniffer to run and having problems. Tried both 0.9.7 and 1.0.1 same results on both. OS is W7-32 home. Hardware, have tried several PCA10000 and a PCA10001...
Hello community, I have the uVision 4 installed, I tried to open the project to compile ble_app_hrs_dfu but get the following error.
I find this file in C:\Keil\C51...
The reference designs and sample layout use 0402 sized components in the RF section. Are 0402 sized components required or can 0603 sized components be used? I'm trying to...
how i can send and receive data by multiple nrf24l01
for example :
If I have 10 packets for send .In Deviec 1 I want send 5 packets by one nrf24l01 and send 5 packeets...
Hi there,
I am struggling for 4-5 days but could find a solution yet.
Can nRF8002 be used as a beacon? I read nrf8002 datasheet and also google it alot but could not see...
If the softdevice is not used, As follows:
static void gpio_init(void)
{
nrf_gpio_cfg_input(Record, NRF_GPIO_PIN_PULLUP);
nrf_gpio_cfg_input(Play, NRF_GPIO_PIN_PULLUP...
There is an input clock signal with frequency of 3MHz-5MHz, but the exact frequency is unknown. I want to use nRF51822 to detect the clock signal's frequency, the accuracy...
Hi, I was using LG's HBS750 (Bluetooth Headset).
This device , after it is connected to an iOS device, shows the headset's battery level.
(Device Spec : Bluetooth 3...
Hi,
When running the multi-role-conn-observer-advertiser example on nrf51822 Soc with S110v7, I never be able to get the MAC address, and even the RSSI is always 0x1.I...
Hi all,
I am trying to implement a scanner (for reading RSSI and MAC address of the advertisor) , and I am based on S120\multilink_central example.
I understood from here...
