Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hi, I'm trying to run ble peripheral and timeslot receiver at the same time. I can see ble advertisements and I can connect to the peripheral. I can also read and write ble...
Hi,
Some questions below about the HID keyboard that refer to the example "/s110/ble_app_hids_keyboard" .
What initialize m_advertising_mode value before to call...
Hello,
to reduce ernergy consumption i use the sd_app_evt_wait() function while the twi is sending or receiving data.
i set nrf_twi->address and nrf_twi->txd and set...
Hello,
I have troubles using spi_master_example.
I want to control by spi a slave device from the nRF, I am sending sequences as expected and my slave device answers me...
The S130 SDS 0.5 documents a CODE_R1_BASE of 0x00020000, but I can't get it to work with code at this location. Any SoftDevice API call ends up in the application's SVC_Handler...
Hi,
i use the library app_gpiote to setup interrupts on a toggling external pin(this pin generates a signal which changes from high to low).The external interrupt signal...
Links: ota_profile_pkt_rcpt_notif
As you see,GAP Disconnection，I don't Know how it works.The ble device call disconnection,but ble android phone respones it more then 5s...
Hi, I'm a student at Oregon State University using the nRF51 Development Kit for a project. I can't seem to find any functions for sending and recieving Bluetooth signals...
HI ALL!
I got a question about establishing my own service.
Currently, I can just send my data through the 'hrs' service(by replacing the heart_rate value with my own...
Hi,
I just downloaded the Utility app for the ble apps(nRF518 SDK) checking on my i5 at iOS 7.1.2. I have tried to connect the apps(hr, proximity) of Utility, but there is...
I changed the dfu start address to 0x00 and application start address to 0x8000.
The application use the RTC0 IRQ to count the timer,
but the RTC0 IRQ did not work correct...
I've been successfully using IAR and I-jet with the 51822 and S110. I can build, download and run under the debugger with no problems.
I recently switched to the 51422...
Has anyone has any success flashing a nRF24LU+ dongle NOT using the official dev kit ? I'm attempting to flash using another microcontroller programmed as an SPI Master so...
I will be happy if someone points out this is a newbie problem and not something weirder...
Running on Win7, 64 bit BTW...
I recently received the nRF51 eval kit. I...
Hi,
I am trying to connect my msp430f1611 microcontroller with the nrf8001 bluetooth chip. I read this thread ( devzone.nordicsemi.com/.../) and it seems very helpful....
