I have followed the instructions in the DevAcademy Cellular IoT Fundamentals Lesson 3 Exercise 1 exactly, (whilist filling in the gaps from the cloned cell-fund repo) and...
I'm working on a IoT device that leverages the AWS IoT and AWS FOTA components from the nRF Connect SDK. The device is battery powered, and so I want to limit the connection...
Hi there,
We have a device that utilizes an NRF52840 chip. Several threads on DevZone - including this one and this one - warn about the dangers of applying voltage to a...
Using FreeRTOS and SDK 15.3 on nRF52840 and SES, SD 140
I'm following along with the NUS example project in this particular release and have a problem I'm a little stumped...
I'm developing firmware for a RAK4630 for IOT purposes. According to the datasheet, the average consumption of the nrf52840 is 1.5 ua in system ON mode. Mine is measuring...
Hi all,
I may have encountered an issue with nrf9151DK board.
When I only set LED1 with dk_set_leds (DK_LED1_MSK) the LED1 and LED2 are both lit.
Setting other leds...
I am using XiP with partial code running from MX25. I am facing issue where I am getting hard faults when Erase is happening and at the same time the ISR from XiP region is...
Hi
Recently I attempted to modify the bootloader.When download the official bootloader, it could modify the value of (NRF_UICR_BASE+0x14).But if I Remove some code，when...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
I'm building the ble_hrs_app for my pca10000, I've made a couple of changes (to change the LEDS which show) and I'm building it with CrossWorks .. which I thought I knew how...
Hello, I'm trying to get my nrf51822 project from SDK 5.0.0 running in the latest SDK 5.2.0. To minimize problems with KEIL I used the template project and copied my sources...
Hello,
I have a nRF51822 Evaluation Kit, and a working ble_app_uart demo software.
I would like use the Fujitsu MBH7BLZ02-109004 module . I can flash and verify the softdevice...
I am using the following code to manage a buffer to put through data to the ble stack. I think I saw a similar code on the nRFready Desktop 2 v1.0.4 examples:
/**@brief...
Are there any pin restrictions for connecting the PWM module to? That is, would I be able to output the a PWM signal (created by the internal PWM facility) through any P0...
Hello Gentlemen,
I'm developing an Android App that needs to connect to nRF. The nRF sensor does not have keyboard, display or buttom.
But we can have OOB which is a...
Hello!
I have two question from Heart Rate Application.
What BLE_L2CAP_MTU_DEF number presents?
I do not see event handlers for WAKEUP_BUTTON and BONDMNGR_DELETE_BUTTON...
Development Board can not be loaded by Keil 4.7.2
nRF51 by Nordic can not be identified by Keil automatically, how to configure the parameter for programming?
The Android API Kitkat documentation says the following about BluetoothSockect.connect()
"This method will block until a connection is made or the connection fails. If...
Hello Gentlemen,
I'm looking for sample code that shows how to enable security which prompts for a PIN number on the Android device when I want to connect to the nRF. ...
On the box for the nRF51822 there's one tiny sticker with nRF6815, Rev 2.2.0, 2014.15 and 10004490 written on it.
I can't find ohter information on the box.
