Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
I'm trying to use nRF51 IoT SDK and setting raspberry pi as router.
When I enter the below command for connecting to nrf51, wlan connection is disconnected.
echo "connect...
My configuration:
NRF51822 v2
TWI
GPIOTE
Issue:
The gpio interrupt does not get triggered. I know that my twi device is changing the state of the gpio3...
Hello, I apologise for this being quite simple as questions go but I was wondering if anyone knew where to begin or if there is any good information out there on how to use...
Hi,
I need use the nrf51822 to connect to PC via usb ble adapter (virtual com port).
The PC side has the USB BLE dongle (adapter).
http://www.amazon.co.uk/Plugable-Bluetooth...
Hi....
Is there any issue in sending a value on a character in button_event_handler? When i tried it disconnection is happening.Am not using button service , just using...
When running the makefiles found in the esb/gcc_rx and esb/gcc_tx folders I get the following errors:
base:gcc_tx jnoble$ make
mkdir _build
"/Users/jnoble/hardware/nrf51822...
I have trouble compiling successfully even the simplest of example codes for the nRF51822 with the Keil MDK-ARM toolchain (v5).
For example, for the "blinky" project, I...
I have ported the example ble_app_beacon from sdk 7.2.0 for use with nrf51422_xxaa and softdevice s310 (v.2.00).
In the function ble_stack_init() there is a call to the...
Hello everyone,
I have two doubts related to pca10001 board:
What is the maximum amount of current
that can be pulled from a single GPIO
pin?
Does the...
Hello,
I just received new rev.3 nrf51822 chips, so I am migrating with my project to newest SDK version.
I installed Keil5 with that smart run-time environment manager...
I would like to send the current status of the battery as a beacon.
ADC and a few resistors and what do I need?
I am currently using nrf51822.
I know nrf51822 to...
I'm trying to port my old project to the newer soft device and SDK (v8.0.0) and just ran into an issue where the app_timer_event_t seems to no longer be defined. My previous...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Is there a UART version of the DFU example that is provided with the new SoftDevice 7.0?
If not how to go about modifying the BLE DFU example to be able to handle UART...
