We urgently need to add support for Band 40 (B40) to our product. Our use case is very specific, and as far as we understand, the NRF91 currently does not support B40. We...
i just rebuilt the code in the beacon_advertiser.zip file attach to this issue for the NRF52232....
the code runs as expected, though consumes about 200uA when sleeping...
We are currently working on a project based on Enhanced ShockBurst (ESB) and would like to use Front-End Module (FEM) support with the nRF21540.
In your Enhanced ShockBurst...
Hi,
In my project I am developing a system to monitor the consumption of electricity taken from the grid. The nRF9160 SiP module is responsible for acquiring analogue signals...
Hi,
USB CDC EPOUT stops working as the USB incoming traffic data rate increases. The symptoms of this issue align with the Errata 199. The workaround for Errata 199 is...
I made some tests with PPK-II in source meter mode by connecting a load resistor in series with a Fluke 8846A ampere meter to the PPK output. A also hooked a GW Instek GDM...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
I want to realize the connection and communication between the broadcaster and the upper computer software nRF Connect...
I need to get three ADC data from acceleration sensor with nrf51822. I tested getting a ADC data using simple_adc_pca10028(Keil_v5/ARM/Pack/NordicSemiconductor/nRF_Examples...
Hello
We are about to move an old design based on the NRF51 to the more powerfull NRF52.
In this context we would like to use some of the new API’s that has been introduced...
Recompile dfu_dual_bank_ble_s132_pca10040 example from SDK v11 with softdevice v3.0 header. DFU is advertised, but not able to connect to it. always timeout,
There are three...
I made a product with nrf51822AC(based on SDK6.1&softdevice7.3), now we want to do BQB testing and I am working on our board's DTM code.
I have tried example "\Nordic\nrf51822...
Hi Nodic:
I use the PCA10028 V1.2.0 board , and use "nRF51_SDK_9.0.0_2e23562" SDK, ..nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_uart\pca10028\s110\arm5_no_packs...
Hi,
In SDK11 I was able to update advertised device name without restart, just handled write on the characteristic and update advertising data (through a second call to...
I'm going through pin_change_int example and can't understand how we tell controller where locate the function for our event.
Probably it occures in channel_port_alloc that...
I'm trying to communicate with an EEPROM chip using SPI. When I run under the debugger, the EEPROM doesn't respond; without the debugger running, it seems to work fine.
...
Hi everyone
I am working with nrf51822 sd 110 v.7.1
If I change from XXAA to XXAC, do I have to change the IRAM settings? If yes, which are the correct settings?
...
Hi ,
I have 2 nrf51 dongle compiled with a code which can scan and advertise ibeacon constantly. Whenever receive advertisement packet from each other , they are able to...
I think similar to but not exactly this question: devzone.nordicsemi.com/.../
Can I get a quick clarification here....
I'd like to encrypt the zip data / application...
Hi everyone,
Somebody knows if its possible and how to configure a Pin code to establish the connection between the nRF51 peripheral and a phone as a central?
Something...
Hello,
The nRF51824 was announced over 3 months ago, is there a datasheet/product spec available anywhere?
My main curiosity is whether the power efficiency has changed...
Hi,
I'm trying to compile a boot loader for the nrf51822. I've downloaded the SDK from the website, and looked at the boot loader example. However I don't see an arm gcc...
