Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
I'm trying to adapt the secure_bootloader example for our custom board with a nRF52832 QFAB with 32kB RAM and 256kB Flash, following the information in this thread:
https...
I'm building a project on top of cli examples:
<SDK>\examples\peripheral\cli
<SDK>\examples\ble_central_and_peripheral\experimental\ble_app_interactive
My goal is...
Hello
I need to setup the the PWM peripheral@ 8MHz with one selectet Channel in DMA mode. For development, I am using the NRF52840 Preview Dev Kit PCA10056 (Q1AAAA). I did...
I have one question, if Nordic can give some confirmation, that Nordic chips can be used together
with Murata XRCGB32M000F1H00R0.
Customer just asks for that I don’t...
Hi,
In my project NRF51422 need to communicate with two peripherals which are supporting only UART communication.
please help me if there is any possibility.
Thanks...
I'm use the app_button lib to deal with button event ,things go well, I assign the push ,release and long push event to button event .
But there came a situation,while the...
I have noticed that when I run in release mode, turn WDT on, write bonding info, clear bonding info, and reset, my application suddenly uses 2mA more and takes 5 minutes ...
Hi all:
My iOS app use iOSDFULibrary to update my ble.But when the device enter into DFU mode ,it disconnected for a while.
This is my log:
2018-11-27 21:00:11.122263...
Hi Nordic.
Now I am working on a BLE smart card and am adding an external power amplifier. For low power consumption, i decided to give power only when I want PCB doesn...
Hi,
I tried to use nRF52 evaluation kit to program my custom board for that I have used Debug port P19 in evaluation kit. It was working in the beginning but after sometime...
Hello,
I tried to follow the instructions in this tutorial: github.com/.../nRF52832-buttonless-dfu-development-tutorial
1) I flashed this file via nrfjprog: examples\dfu...
The power estimation tool on https://devzone.nordicsemi.com/power/ maxes out at a minimum interval of 7.5ms and a maximum payload of 27 bytes, with 824mA average current....
Hi,
We need to develop an android app that can only scan a nordic ble and send out advertisment packet in our own customised UI and format. Getting the NRF_connect android...
Hi . .
I want to read the data and sent over ble UART app (via ble )
For that I am using Twi sensor ,in order to send the data what are the changes I need to do in twi...
