Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I want to let nRF9160DK communicate with an external module through UART in nRF9160DK
Then I need to assign rx and tx on two pins.
I will use UART0 for printk function...
Hey all!
I have a problem with my custom board using the nRF52832 with Softdevice 6.0 and SKD 15.0.0 working on Windows 10 in SEGGER with the BMD-300. I have the following...
We're using an nRF52832, SDK14.0.0, SoftDevice 132 v5.
Early in our firmware lifecycle, before SoftDevice is enabled, we configure our PMIC. This involves performing some...
I used SDK is nRF5_SDK_14.1.0_1dda907
Chip is nrf52832 evb.
Soft device is S332.
I call function sd_power_system_off() enter system off.
Use triggered from DETECT...
Hi..
I have try to lookup in devzone q&a, but seems not yet found the similar question or answer. Have try SR3 SDK and able to implement keyboard+consumer control for remote...
Hi Sir,
As runs w/ serial DFU and check the source code of nrfutil, it support to send the rest of page when transmitted the data.
1. If we don't want to implement this...
I want to advertise coded phy and 1M. This isn't possible at the same time so I am using the ble_gap_adv_params_t duration to timeout my 1M advertising every 600 ms to switch...
Hello,
I am building an application where client sends a fixed number of packets (10Bytes/packet) to a server with different values of advertisement interval. I changed...
Hi,
I'm developing a smartwatch that relies on low latency communication with local web servers. I'm in the very begining but I'm sure that the latency added between the...
Hello, I need to use MQTT over NB IoT with nRF9160. Task to connect to Amazon AWS over NB IoT with MQTT. As I understand correctly, NB IoT doesn't support TCP, so I can't...
Hi,
I was trying to download nrf5_sdk_for_mesh_v3.1.0_src.zip, which is at : https://www.nordicsemi.com/Software-and-Tools/Software/nRF5-SDK-for-Mesh/Download#infotabs,...
Hi all, I am working on a project for which I use nRF52832 with SDK15.2 and SD132. What I need is that nRF52 should transmit and receive command through serial UART as a central...
Hi, I am trying to setup a mesh architecture, and I am not sure which path to take (Thread / Zigbee / Etc). The architecture is for the following system.
There will be...
hello, i am trying an example of a Node running multi-peripheral with ble_nus service. I have a question: Suppose when Node receives a packet from central A, Node will call...
