Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
sdk12.3.0 In the ble_app_hrs_rscs_relay example, I added the uart_init function referring to the ble_uart example, but when I execute the APP_UART_FIFO_INIT () function, a...
My development environment is PCA10028, SoftDevice 130, SDK12.3.0
Two nRF51822s were mounted in one board One nRF51822 will be used as a TWI master and the other as a TWI...
It is said that ble5.0 can cover a range of 300m, I wonder how big is current when this is achieved? For 52840, the largest power output is 8dBm, for 52832, the largest output...
Hi,everybody!
I use nRF52832,supply volt 3.0V normal, program can be downloaded , run and debug,i ensure the program is accurately.To control a gpio P0.09,on the hardware...
Dear Nordic,
I debug the SDK15 example project ble_app_template_pac10056_s140 project, nothing change, but it will jump into app_error_weak.c as below picture, please help...
I can not get information about the power consumption when twi is enabled and idle. It just state the current when it is running. So do I need to disble it when it is idle...
Greetings,
We have taken the RAM Retention example and are experiencing a failure (all LEDs on) when setting MAX_TEST_ITERATIONS to a value greater than 1. This is duplicated...
I am using nrf51822 with softdevice 7.3 and sdk6. I am having some strange problems in single bank bootloader. The nrftoolbox version 2.4.0 gets stuck at 94% during the firmware...
Hi,
(SDK v14.2, nRF52832)
I'm developing a Timeout Timer functionality, and was wandering if the following scenario is a good practice:
I don't want to have a interrupt...
Good morning everyone,
I am having a lot of problems configuring the Peer Manager.
I read several discussions on the topic, but either they are old (referring to ble_evt_dispatch...
Hello everyone,
I`ve 4 thingys and ran the https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo . That works well.
Now I`m trying to add the nRF52 DK as a Node...
I am trying to perform a dfu upgrade according to: infocenter.nordicsemi.com/index.jsp
The exact command I am running is: nrfutil dfu ble -ic NRF52 -pkg dev_board_bl.zip...
There is something I want you to tell. Do you know how to allow other interrupts (specifically IRQ pin) while interrupting app_timer? I studied variously, but I can not find...
While I'm waiting on answers to other questions, I thought I would try to nrf_Logging with the Segger RTT up and running. It sounds like a pretty tool.
I have created a...
As picture, This is the external circuit of 52832, and I've drawn out P0.09,P0.10,P0.17,P0.18,P0.19,P0.22 of these six gpios, each of them for control purposes, and now P2...
