Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I have troubles with connection using nrf51822 and android phones:
First I connect and bond the device to the phone and it works ok.
Then I periodically...
Hiya,
Regarding voltage amplitude peak to peak for external high-swing clock HFXO 32MHz, what's supply rails？I don't find out this specification defined in datasheet PS_V1...
My phone is like beacon that transmit service data.
(I checked service data in different phone.)
scandata.png
So, I want to recieve service data, service UUID with...
Hello,
I am really new to the field, I apologise, if things I am saying do not make sense, explanations and corrections appreciated :) I am trying to reach IPv4 internet...
Hello,
I would like to make use of an external ADC that is connected to my nRF52832 through SPI & easyDMA,minimizing the use of the CPU (or without using the CPU).
The...
Hi all,
I am started my project using the softdevice S130 v2.0.1 and the ble_app_uart example(SDK11) on a custom board with the nRF51822. I had to made some changes for...
Hi,
after porting an existing application from version 3.0 of the s132 SD to version 5.0, I experience, that sd_ble_gatts_rw_authorize_reply() returns NRF_ERROR_INVALID_PARAM...
I want to use the SPI in master mode, but the slave just have three lines,the miso and the mosi is the same line,but I don't know how to config the pins? Do the nRF52832 supports...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
I am trying to wrap BLE into a nice c++ class.
For this i am using ble_app_uart example.
I think it was working fine until i was up to clean the helper functions.
After...
Hello,
I have a nRF52 as central and a cc2650 as peripheral, when I received advertising answer, I can't see the full size of advertising data (see 7 instead of 31). With...
Another programmer developed the nRF52832 source code using IAR.
But I want to use Keil uVision.
So please tell me how to convert IAR project file to KEIL uVision Project...
Hi!
Using SDK 14, nRF52382, used ble_template to develop a custom app.
I have problems with BLE_GATTS_EVT_WRITE not being called.
I do not use auth. My custom ble sevice...
