Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
hi .
i did what this linke says
but it get me these error
..\main.c(632): error: #20: identifier "NRF_CLOCK_LFCLKSRC_RC_250_PPM_TEMP_8000MS_CALIBRATION" is undefined...
Hi,
I've got some really simple code I've been trying to get working with SPI on nRF52 (while also using SoftDevice):
///MISO, MOSI, SCK set, but SS not
err_code =...
I am trying to figure out if I need to disable the softdevice to get the power numbers in to the single-digit uA range.
With the softdevice loaded/enabled, but with the...
I'm developing nRF52832 to implement the Eddystone (※ 1).
But i'm thinking seriously about what can I do to have the Eddystone Specification and compatibility.
please...
I am working with the ble_app_buttonless_dfu example and am wondering why the example sends 2 notification messages in response to a command being written to it? This occurs...
Hello,
I'm using nRF51, SDK10, S110 beacon example with dfu service.
What I have done are listed as below:
merged softdevice8.0 and bootloader to sd_bl.hex and...
hi,
in FreeRTOSConfig.h file,
#define configUSE_TICKLESS_IDLE 1
#define configUSE_IDLE_HOOK 1
and the idlehook function
void vApplicationIdleHook( void )
{
__WFI;...
I have got PCA10040 development board having nRF52832 nordic ble chip. I am not able to get datasheet for this. I have to use SPI communication on this board but I am confused...
Hai i am new embedded designer.. I am working with nrf52832 , i need to get accelerometer and gyroscope data from mpu6050 through twi.. Can any one give me a sample code ...
I am trying to wake my processor from sleep after issuing the sd_app_evt_wait(); Using an interrupt on an external RTC chip, I send interrupt pulses to the nRF at 1Hz. At...
Hi guys,
I have two nrF51 dongles and I am really interested in making the pairing of both of them using the proximity search feature of ANT. So far what I did is, I took...
Hi.
I have a BLE peripheral app for the nRF51822. I'm using SDK 12.1.0 with SD 130 v2.0.1 and gcc. I'm implementing DFU OTA at the moment and I notice there are two builds...
Hi,
I have an old project running on nRF51822, with SoftDevice SDK v8 - S110 mode.
I'm trying to migrate the project to a nRF52832 with SoftDevice SDV v12 - S132 v3 mode...
